Get 20M+ Full-Text Papers For Less Than $1.50/day. Start a 14-Day Trial for You or Your Team.

Learn More →

Variation of thin film deposition rate on SS 314 with the variation of gas flow rate using CVD

Variation of thin film deposition rate on SS 314 with the variation of gas flow rate using CVD Purpose – Solid thin films have been deposited on stainless steel 314 (SS 314) substrates in a chemical vapor deposition (CVD) reactor at different flow rates of natural gas mostly methane (CH 4 ). The purpose of this paper was to investigate experimentally the variation of thin film deposition rate with the variation of gas flow rate. Design/methodology/approach – During experiment, the effect of gap between activation heater and substrate on the deposition rate has also been observed. To do so, a hot filament thermal CVD unit is used. The flow rate of natural gas varies from 0.5 to 2 l/min at normal temperature and pressure and the gap between activation heater and substrate varies from 4 to 6.5 mm. Findings – Results show that deposition rate on SS 314 increases with the increase of gas flow rate. It is also seen that deposition rate increases with the decrease of gap between activation heater and substrate within the observed range. These results are analyzed by dimensional analysis to correlate the deposition rate with gas flow rate, surface roughness and film thickness. In addition, friction coefficient and wear rate of SS 314 sliding against SS 304 under different normal loads are also investigated before and after deposition. The obtained results reveal that the values of friction coefficient and wear rate are lower after deposition than that of before deposition. Originality/value – In this study, thin film deposition rate on SS 314 was investigated using CVD. The obtained results were analyzed by dimensional analysis to correlate the deposition rate with gas flow rate, surface roughness and film thickness. The friction coefficient and wear rate of SS 314 were also examined before and after deposition. http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.png Industrial Lubrication and Tribology Emerald Publishing

Variation of thin film deposition rate on SS 314 with the variation of gas flow rate using CVD

Loading next page...
 
/lp/emerald-publishing/variation-of-thin-film-deposition-rate-on-ss-314-with-the-variation-of-dsZ0bt5eEx

References (18)

Publisher
Emerald Publishing
Copyright
Copyright © 2011 Emerald Group Publishing Limited. All rights reserved.
ISSN
0036-8792
DOI
10.1108/00368791111169016
Publisher site
See Article on Publisher Site

Abstract

Purpose – Solid thin films have been deposited on stainless steel 314 (SS 314) substrates in a chemical vapor deposition (CVD) reactor at different flow rates of natural gas mostly methane (CH 4 ). The purpose of this paper was to investigate experimentally the variation of thin film deposition rate with the variation of gas flow rate. Design/methodology/approach – During experiment, the effect of gap between activation heater and substrate on the deposition rate has also been observed. To do so, a hot filament thermal CVD unit is used. The flow rate of natural gas varies from 0.5 to 2 l/min at normal temperature and pressure and the gap between activation heater and substrate varies from 4 to 6.5 mm. Findings – Results show that deposition rate on SS 314 increases with the increase of gas flow rate. It is also seen that deposition rate increases with the decrease of gap between activation heater and substrate within the observed range. These results are analyzed by dimensional analysis to correlate the deposition rate with gas flow rate, surface roughness and film thickness. In addition, friction coefficient and wear rate of SS 314 sliding against SS 304 under different normal loads are also investigated before and after deposition. The obtained results reveal that the values of friction coefficient and wear rate are lower after deposition than that of before deposition. Originality/value – In this study, thin film deposition rate on SS 314 was investigated using CVD. The obtained results were analyzed by dimensional analysis to correlate the deposition rate with gas flow rate, surface roughness and film thickness. The friction coefficient and wear rate of SS 314 were also examined before and after deposition.

Journal

Industrial Lubrication and TribologyEmerald Publishing

Published: Sep 27, 2011

Keywords: Deposition rate; Gas flow rate; Gap; Dimensional analysis; Friction; Wear

There are no references for this article.