Get 20M+ Full-Text Papers For Less Than $1.50/day. Start a 14-Day Trial for You or Your Team.

Learn More →

Using statistically designed experiment to optimize vacuum-assisted post-processing of binder jetted specimens

Using statistically designed experiment to optimize vacuum-assisted post-processing of binder... This paper aims to propose a vacuum-assisted post-processing method for use in binder jetted technology. The method is based on six key technological parameters and uses standard, commercially available consumables to achieve improvement in tensile strength, as well as the microstructure and porosity of the infiltrated matrix.Design/methodology/approachSix key technological parameters were systematically varied as factors on three levels, using design of experiment, i.e. definitive screening design. Surface response methodology was used to optimize the process and yield optimal tensile strength for the given range of input factors. Thus obtained, the optimized factor settings were used in a set of confirmation runs, where the result of optimization was experimentally confirmed. To confirm improvement in microstructure of the infiltrated matrix, SEM analysis was performed, while the reduction of porosity was analyzed using mercury porosimetry.FindingsThe obtained results indicate that, compared to its conventional counterpart, the proposed, optimized infiltration method yields improvement in tensile strength which is significant from both the statistical and engineering point of view, while reducing porosity by 3.5 times, using only standard consumables. Scanning electron microscopy examination of fractured specimens’ micrographs also revealed significant morphological differences between the conventional and proposed method of post-processing. This primarily reflects in higher surface area under hardened epoxy infiltrate, which contributes to increased load capacity of specimen cross-section.Research limitations/implicationsAt the present stage of development, the most important limitation of the proposed method is the overall size of models which can be accommodated in standard vacuum impregnation units. Although, in this study, the infiltration method did not prove statistically significant, further investigation is required with models of complex geometry, various sizes and mass arrangements, where infiltration would be more challenging and could possibly result in different findings.Practical implicationsThe most important practical implication of this study is the experimentally verified result of optimization, which showed that tensile strength and matrix microstructure can be significantly improved, using just standard consumables.Social implicationsImproved strength contributes to reduction of material consumption, which, in a longer run, can be beneficial for environment protection and sustainable development.Originality/valueBased on literature review, there have been no previous investigations which studied the tensile strength of infiltrated specimens through design of experiment, which involved specimen preheating temperature, level and duration of vacuum treatment of infiltrate mixture and infiltrated specimens and infiltration method. http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.png Rapid Prototyping Journal Emerald Publishing

Using statistically designed experiment to optimize vacuum-assisted post-processing of binder jetted specimens

Movrin, Dejan; Luzanin, Ognjan; Guduric, Vera
Rapid Prototyping Journal , Volume 25 (3): 11 – Apr 16, 2019
Download PDF
11 pages

Loading next page...
 
/lp/emerald-publishing/using-statistically-designed-experiment-to-optimize-vacuum-assisted-Jey5180mY0
Publisher
Emerald Publishing
Copyright
© Emerald Publishing Limited
ISSN
1355-2546
DOI
10.1108/rpj-07-2018-0177
Publisher site
See Article on Publisher Site

Abstract

This paper aims to propose a vacuum-assisted post-processing method for use in binder jetted technology. The method is based on six key technological parameters and uses standard, commercially available consumables to achieve improvement in tensile strength, as well as the microstructure and porosity of the infiltrated matrix.Design/methodology/approachSix key technological parameters were systematically varied as factors on three levels, using design of experiment, i.e. definitive screening design. Surface response methodology was used to optimize the process and yield optimal tensile strength for the given range of input factors. Thus obtained, the optimized factor settings were used in a set of confirmation runs, where the result of optimization was experimentally confirmed. To confirm improvement in microstructure of the infiltrated matrix, SEM analysis was performed, while the reduction of porosity was analyzed using mercury porosimetry.FindingsThe obtained results indicate that, compared to its conventional counterpart, the proposed, optimized infiltration method yields improvement in tensile strength which is significant from both the statistical and engineering point of view, while reducing porosity by 3.5 times, using only standard consumables. Scanning electron microscopy examination of fractured specimens’ micrographs also revealed significant morphological differences between the conventional and proposed method of post-processing. This primarily reflects in higher surface area under hardened epoxy infiltrate, which contributes to increased load capacity of specimen cross-section.Research limitations/implicationsAt the present stage of development, the most important limitation of the proposed method is the overall size of models which can be accommodated in standard vacuum impregnation units. Although, in this study, the infiltration method did not prove statistically significant, further investigation is required with models of complex geometry, various sizes and mass arrangements, where infiltration would be more challenging and could possibly result in different findings.Practical implicationsThe most important practical implication of this study is the experimentally verified result of optimization, which showed that tensile strength and matrix microstructure can be significantly improved, using just standard consumables.Social implicationsImproved strength contributes to reduction of material consumption, which, in a longer run, can be beneficial for environment protection and sustainable development.Originality/valueBased on literature review, there have been no previous investigations which studied the tensile strength of infiltrated specimens through design of experiment, which involved specimen preheating temperature, level and duration of vacuum treatment of infiltrate mixture and infiltrated specimens and infiltration method.

Journal

Rapid Prototyping Journal – Emerald Publishing

Published: Apr 16, 2019

Keywords: Tensile strength; Microstructure; Post-processing; Definitive screening design (DSD); Infiltration; Binder jetting

References

  • The research status and development trend of additive manufacturing technology
    Chen, L.; He, L.; Yang, Y.; Ni, S.; Ren, H.
  • Effects of position, orientation, and infiltrating material on three dimensional printing models
    Frascati, J.
  • Tensile properties of processed 3D printer ZP150 powder material
    Gharaie, S.H.; Morsi, Y.; Masood, S.H.
  • A comprehensive assessment on the impact of post-processing variables on tensile, compressive and bending characteristics for 3D printed components
    Impens, D.; Urbanic, R.J.
  • Confirmation runs in design of experiments
    Jensen, W.A.
  • A class of three-level designs for definitive screening in the presence of second-order effects
    Jones, B.; Nachtsheim, C.J.
  • Effective design-based model selection for definitive screening designs
    Jones, B.; Nachtsheim, C.J.
  • Application of polymer plaster composites in additive manufacturing of high-strength components
    Junk, S.; Matt, R.
  • Mechanical properties of commercial rapid prototyping materials
    Kotlinski, J.
  • Investigating impact of five build parameters on the maximum flexural force in FDM specimens – a definitive screening design approach
    Luzanin, O.; Guduric, V.; Ristic, I.; Muhic, S.
  • Property enhancement of 3D-printed alumina ceramics using vacuum infiltration
    Maleksaeedi, S.; Eng, H.; Wiria, F.E.; Ha, T.M.H.; He, Z.
  • Influence of processing parameters on creep and recovery behavior of FDM manufactured part using definitive screening design and ANN
    Mohamed, O.A.; Masood, S.H.; Bhowmik, J.L.
  • Post-process influence of infiltration on binder jetting technology
    Ocaña, G.E.; Alves, J.L.; Neto, R.J.
  • Fiji: an open-source platform for biological-image analysis
    Schindelin, J.; Arganda-Carreras, I.; Frise, E.; Kaying, V.; Longair, M.; Pietzsch, T.; Preibisch, S.; Rueden, C.; Saalfeld, S.; Schmid, S.; Tinevez, J.Y.; White, D.J.; Hartestein, V.; Eliceiri, K.; Tomancak, P.; Cardona, A.
  • Improvement in mechanical properties of three – dimensional printing parts made from natural polymers reinforced by acrylate resin for biomedical applications: a double infiltration approach
    Suwanprateeb, J.
  • A review of process development steps for new material systems in three dimensional printing (3DP)
    Utela, B.; Storti, D.; Anderson, R.; Ganter, M.
  • Modified curing protocol for improved strength of binder-jetted 3D parts
    Watters, M.; Bernhardt, M.
  • Constructing definitive screening designs using conference matrices
    Xiao, L.; Lin, D.J.; Bai, F.