Get 20M+ Full-Text Papers For Less Than $1.50/day. Start a 14-Day Trial for You or Your Team.

Learn More →

Multi-objective optimization for optimum abrasive water jet machining process parameters of Inconel718 adopting the Taguchi approach

Multi-objective optimization for optimum abrasive water jet machining process parameters of... The purpose of this paper is to adopt the multi-objective optimization technique for identifying a set of optimum abrasive water jet machining (AWJM) parameters to achieve maximum material removal rate (MRR) and minimum surface roughness.Design/methodology/approachData of a few experiments as per the Taguchi’s orthogonal array are considered for achieving maximum MRR and minimum surface roughness (Ra) of the Inconel718. Analysis of variance is performed to understand the statistical significance of AWJM input process parameters.FindingsEmpirical relations are developed for MRR and Ra in terms of the AWJM process parameters and demonstrated their adequacy through comparison of test results.Research limitations/implicationsThe signal-to-noise ratio transformation should be applied to take in to account the scatter in the repetition of tests in each test run. But, many researchers have adopted this transformation on a single output response of each test run, which has no added advantage other than additional computational task. This paper explains the impact of insignificant process parameter in selection of optimal process parameters. This paper demands drawbacks and complexity in existing theories prior to use new algorithms.Practical implicationsTaguchi approach is quite simple and easy to handle optimization problems, which has no practical implications (if it handles properly). There is no necessity to hunt for new algorithms for obtaining solution for multi-objective optimization AWJM process.Originality/valueThis paper deals with a case study, which demonstrates the simplicity of the Taguchi approach in solving multi-objective optimization problems with a few number of experiments. http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.png 2nd Multidiscipline Modeling in Materials and Structures Emerald Publishing

Multi-objective optimization for optimum abrasive water jet machining process parameters of Inconel718 adopting the Taguchi approach

Download PDF
16 pages

Loading next page...
 
/lp/emerald-publishing/multi-objective-optimization-for-optimum-abrasive-water-jet-machining-q20karM5jL
Publisher
Emerald Publishing
Copyright
© Emerald Publishing Limited
ISSN
1573-6105
DOI
10.1108/mmms-10-2018-0175
Publisher site
See Article on Publisher Site

Abstract

The purpose of this paper is to adopt the multi-objective optimization technique for identifying a set of optimum abrasive water jet machining (AWJM) parameters to achieve maximum material removal rate (MRR) and minimum surface roughness.Design/methodology/approachData of a few experiments as per the Taguchi’s orthogonal array are considered for achieving maximum MRR and minimum surface roughness (Ra) of the Inconel718. Analysis of variance is performed to understand the statistical significance of AWJM input process parameters.FindingsEmpirical relations are developed for MRR and Ra in terms of the AWJM process parameters and demonstrated their adequacy through comparison of test results.Research limitations/implicationsThe signal-to-noise ratio transformation should be applied to take in to account the scatter in the repetition of tests in each test run. But, many researchers have adopted this transformation on a single output response of each test run, which has no added advantage other than additional computational task. This paper explains the impact of insignificant process parameter in selection of optimal process parameters. This paper demands drawbacks and complexity in existing theories prior to use new algorithms.Practical implicationsTaguchi approach is quite simple and easy to handle optimization problems, which has no practical implications (if it handles properly). There is no necessity to hunt for new algorithms for obtaining solution for multi-objective optimization AWJM process.Originality/valueThis paper deals with a case study, which demonstrates the simplicity of the Taguchi approach in solving multi-objective optimization problems with a few number of experiments.

Journal

2nd Multidiscipline Modeling in Materials and Structures – Emerald Publishing

Published: Feb 5, 2020

Keywords: Inconel718; Abrasive water jet machining (AWJM); Analysis of variance (ANOVA); Material removal rate (MRR); Surface roughness (Ra)

References

  • Parameters optimization and objective trend analysis for fiber laser keyhole welding based on Taguchi – FEA
    Ai, Y.; Wang, J.; Jiang, P.; Liu, Y.; Liu, W.
  • Simultaneous optimization of multiple quality characteristics in manufacturing processes using Taguchi’s quality loss function
    Antony, J.
  • Analysis of WEDM process parameters on surface roughness and kerf using Taguchi method
    Banu, A.; Bakar, M.A.; Ali, M.Y.; Adesta, E.Y.T.
  • Optimum WEDM process parameters of SS304 using Taguchi method
    Bharathi, P.; Priyanka, T.G.L.; Srinivasa Rao, G.; Nageswara Rao, B.
  • Optimization of process parameters during end milling and prediction of work piece temperature rise
    Bhirudi, N.L.; Gawande, R.R.
  • An innovative methodology for the performance evaluation of coated cemented carbide inserts in milling of Inconel718
    Bouzakis, K.D.; Michailidis, N.; Gerardis, S.; Batsiolas, M.; Papa, M.; Lili, E.; Mirisidis, J.; Mueller, J.; Cremer, R.
  • Parametric optimization of abrasive water jet machining processes using grey wolf optimizer
    Chakraborty, S.; Mitra, A.
  • Surface roughness prediction by extreme learning machine constructed with abrasive water jet
    Cojbasic, Z.; Petkovic, D.; Shamshirband, S.; Tong, C.W.; Sudheer, C.; Jankovic, P.; Ducic, N.; Baralic, J.
  • Optimization of the physical and mechanical properties of a spline surface fabricated by high-speed cold roll beating based on Taguchi theory
    Cui, F.; Su, Y.; Xu, S.; Liu, F.; Yao, G.
  • High speed machining of Inconel718: tool wear and surface roughness analysis
    D’Addona, D.M.; Raykar, S.J.; Narke, M.M.
  • Optimization of process parameters in friction stir welding of dissimilar aluminium alloys (AA5083 and AA6061) using Taguchi technique
    Devaiah, D.; Kishore, K.; Laxminarayana, P.
  • Optimization of machining parameters in face milling using multi-objective Taguchi technique
    Fedai, Y.; Khraman, F.; Akin, H.K.; Basar, G.
  • Multi performance optimization in turning of free-machining steel using Taguchi method and utility concept
    Gaitonde, V.N.; Karnik, S.R.; Paulo Davim, J.
  • Investigation on the cutting quality characteristics of abrasive water jet machining of AA6061-B4C-hBN hybrid metal matrix composites
    Gnanavelbabu, A.; Rajkumar, K.; Saravanan, P.
  • Modelling the cutting process and cutting performance in abrasive water jet machining using genetic-fuzzy approach
    Jai Aultrin, K.S.; Dev Anand, M.; Jerald Jose, P.
  • Optimization of process parameters on commercial mild steel using Taguchi technique
    Jaiganesh, V.; Yokesh Kumar, B.; Sevvel, P.; Balaji, A.J.
  • Application of Taguchi approach and utility concept in solving the multi-objective problem when turning AISI 202 austenitic stainless steel
    Kaladhar, M.; Subbaiah, K.V.; Srinivasa Rao, C.; Narayana Rao, K.
  • AWJM performance of jute/polyester composite using MOORA and analytical models
    Kalirasu, S.; Rajini, N.; Rajesh, S.; Jappes, J.T.W.; Karuppasamy, K.
  • Technological and economical assessment of alternative process chains for Blisk manufacture
    Klocke, F.; Schmitt, R.; Zeis, M.; Heidemanns, L.; Kerkhoff, J.; Heinen, D.; Klink, A.
  • Parametric optimization of abrasive water jet machining of Inconel718 material
    Kubade, P.R.; Patil, P.; Bidgar, A.; Papti, A.; Potdar, P.; Kshirsagar, R.G.
  • Multi-response optimization of AWJM process parameters on machining TiB2 particles reinforced Al7075 composite using Taguchi-DEAR methodology
    Manoj, M.; Jinu, G.R.; Muthuramalingam, T.
  • Model development for mechanical properties and weld quality class of friction stir welding using multi-objective Taguchi method and response surface methodology
    Mohamed, M.A.; Manurung, Y.H.; Berhan, M.N.
  • Investigation of water jet peening process parameters on AL6061-T6
    Muruganandhan, R.; Mugilvalavan, M.; Thirumavalavan, K.; Yuvaraj, N.
  • Modeling and optimization of process parameters during AWJM machining of die steel
    Patel, D.; Patel, V.
  • Improving the quality characteristics of abrasive water jet machining of marble material using multi-objective artificial bee colony algorithm
    Pawar, P.J.; Umesh, S.V.; Mangesh, Y.K.
  • Experimental research into alternative abrasive material for the abrasive water-jet cutting of titanium
    Perec, A.
  • Machinability performance of Al–NiTi and Al–NiTi–nano SiC composites with parametric optimization using GSA
    Purusothaman, M.; Jayamani, M.; Sekarbabu, B.; Jeya Prakash, K.; Nagarajan, R.; Sultan, M.T.H.; Rajesh, S.
  • Transitioning to sustainable production – Part I: application on machining technologies
    Pusavec, F.; Krajnik, P.; Kopac, J.
  • Optimization of abrasive water jet machining using multi-objective cuckoo search algorithm
    Qiang, Z.; Miao, X.; Wu, M.; Sawhney, R.
  • Process parameter optimization of friction stir welding of aluminium 2014-T651 alloy using Taguchi technique
    Rajeesh, J.; Balamurugan, R.; Balachandar, K.
  • Optimum drilling parameters of coir fibre-reinforced polyester composites
    Rajeev Kumar, D.; Varma, P.S.S.K.; Nageswara Rao, B.
  • Expected range of the output response for the optimum input parameters utilizing the modified Taguchi approach
    Rajyalakshmi, K.; Nageswara Rao, B.
  • Modified Taguchi approach to trace the optimum GMAW process parameters on weld dilution for ST-37 steel plates
    Rajyalakshmi, K.; Nageswara Rao, B.
  • Modelling and multi objective optimization of laser peening process using Taguchi utility concept
    Ranjith Kumar, G.; Rajyalakshmi, G.
  • Optimization of cutting parameters to minimize the surface roughness in the end milling process using the Taguchi method
    Ribeiro, J.; Lopes, H.; Queijo, L.; Figueiredo, D.
  • Surface properties and fatigue failure analysis of alloy 718 surfaces milled by abrasive and plain water jet
    Rivero, A.; Alberdi, A.; Artaza, T.; Mendia, L.; Lamikiz, A.
  • Optimum WEDM process parameters of Incoloy®Alloy800 using Taguchi method
    Sahiti, M.; Raghavendra Reddy, M.; Joshi, B.; Peter Praveen, J.; Nageswara Rao, B.
  • Performance analysis of abrasive water jet machining process for AISI 304 stainless steel
    Sanghani, C.R.; Korat, M.M.
  • A study on kerf characteristics of hybrid aluminium 7075 metal matrix composites machined using abrasive water jet machining technology
    Sasikumar, K.S.K.; Arulshri, K.P.; Ponappa, K.; Uthayakumar, M.
  • Application of Taguchi approach to seek optimum drilling parameters for woven fabric carbon fibre/epoxy laminates
    Sastry, K.S.S.; Manideep Kumar, K.V.D.S.R.; Priyanka, M.; Raghu Ram, M.; Nageswara Rao, B.
  • Optimization of abrasive water jet machining process parameters using Taguchi grey rational analysis (TGRA)
    Satyanarayana, B.; Srikar, G.
  • Identification of optimum laser beam welding process parameters for E110 zirconium alloy butt joint based on Taguchi-CFD simulations
    Satyanarayana, G.; Narayana, K.L.; Nageswara Rao, B.
  • Experimental study on abrasive water jet machining of AA5083 in a range of thicknesses
    Selvakumar, G.; Prakash, S.S.R.; Lenin, N.
  • Experimentation investigation of abrasive water jet machining parameters using Taguchi and evolutionary optimization techniques
    Shukla, R.; Singh, D.
  • A review on parameters optimization in abrasive water jet cutting
    Sonawane, N.K.; Khalkar, M.Y.; Shinde, V.B.
  • Taguchi optimization of cutting parameters in turning AISI 1020 MS with M2 HSS tool
    Sonowal, D.; Sarma, D.; Barua, P.B.; Nath, T.
  • ANN and RSM approach for modelling and multi objective optimization of abrasive water jet machining process
    Srinath Reddy, N.; Tirumala, D.; Rajyalakshmi, G.; Das, R.
  • Empirical modelling and optimization of kerf width in abrasive water jet machining – a short review
    Subbaiah, K.V.; Baburaja, K.
  • The optimization of multi-response problems in the Taguchi method
    Tong, L.I.; Su, C.T.; Wang, C.H.
  • Machinability of nickel-based superalloy by abrasive water jet machining
    Uthayakumar, M.; Khan, M.A.; Kumaran, S.T.; Slota, A.; Zajac, J.
  • Optimizing the process parameters of WJM using Taguchi method and ANOVA of Inconel 625
    Viswanath, J.; Lakshmi Tulasi, C.; Anand Babu, K.
  • Optimization of laser brazing onto galvanized steel based on ensemble of metamodels
    Zhou, Q.; Rong, Y.; Shao, X.; Jiang, P.; Gao, Z.; Cao, L.