Get 20M+ Full-Text Papers For Less Than $1.50/day. Start a 14-Day Trial for You or Your Team.

Learn More →

Mechanical drilling of PCB micro hole and its application in micro ultrasonic powder molding

Mechanical drilling of PCB micro hole and its application in micro ultrasonic powder molding Purpose – This paper aims to present the main factors affecting the mechanical drilling of the printed circuit board (PCB for short) micro-holes and method of micro-ultrasonic powder molding (micro-UPM for short) by utilizing PCB micro-hole array. Design/methodology/approach – To optimize the drilling process, the paper proposes the on-line monitoring methods for the drilling process including drilling force, drilling temperature, high-speed photography and vibration signals. Taking 0.10 and 0.15 mm micro-drilling as examples, the paper analyzes the drilling process of ultra-small micro-holes. Finally, by taking the PCBs with 0.10 and 0.15 mm micro-hole arrays as the micro-cavity inserts, utilizing ultra-high-molecule weight polyethylene powder with the average particle size of about 150 μm as raw material, two sizes of micro-cylinder array polymer parts are fabricated through micro-UPM process. Findings – PCB micro-cavity inserts with micro-hole arrays fabricated by mechanical drilling has the advantages of low costs, high efficiency and good consistency. Taking 0.10 and 0.15 mm micro-drilling as examples, it is found that the both measured apertures are about 10.0 μm more than the diameter of the micro-drill bits on average. The average diameter of the micro-cylinders by micro-UPM process is smaller than that of the micro-hole with the same specification, while the value of the roughness of the cylinder surface is more than that of the hole-wall surface with the same specification. Originality/value – This paper describes the challenges and the developments of mechanical drilling and by using PCB micro-cavity inserts with micro-hole arrays fabricated by mechanical drilling, two different micro-cylinder array polymer parts are successfully made and thus the application area of PCB micro-drilling is broadened. http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.png Circuit World Emerald Publishing

Mechanical drilling of PCB micro hole and its application in micro ultrasonic powder molding

Loading next page...
 
/lp/emerald-publishing/mechanical-drilling-of-pcb-micro-hole-and-its-application-in-micro-qjNTnxbMBN

References (15)

Publisher
Emerald Publishing
Copyright
Copyright © Emerald Group Publishing Limited
ISSN
0305-6120
DOI
10.1108/CW-12-2014-0057
Publisher site
See Article on Publisher Site

Abstract

Purpose – This paper aims to present the main factors affecting the mechanical drilling of the printed circuit board (PCB for short) micro-holes and method of micro-ultrasonic powder molding (micro-UPM for short) by utilizing PCB micro-hole array. Design/methodology/approach – To optimize the drilling process, the paper proposes the on-line monitoring methods for the drilling process including drilling force, drilling temperature, high-speed photography and vibration signals. Taking 0.10 and 0.15 mm micro-drilling as examples, the paper analyzes the drilling process of ultra-small micro-holes. Finally, by taking the PCBs with 0.10 and 0.15 mm micro-hole arrays as the micro-cavity inserts, utilizing ultra-high-molecule weight polyethylene powder with the average particle size of about 150 μm as raw material, two sizes of micro-cylinder array polymer parts are fabricated through micro-UPM process. Findings – PCB micro-cavity inserts with micro-hole arrays fabricated by mechanical drilling has the advantages of low costs, high efficiency and good consistency. Taking 0.10 and 0.15 mm micro-drilling as examples, it is found that the both measured apertures are about 10.0 μm more than the diameter of the micro-drill bits on average. The average diameter of the micro-cylinders by micro-UPM process is smaller than that of the micro-hole with the same specification, while the value of the roughness of the cylinder surface is more than that of the hole-wall surface with the same specification. Originality/value – This paper describes the challenges and the developments of mechanical drilling and by using PCB micro-cavity inserts with micro-hole arrays fabricated by mechanical drilling, two different micro-cylinder array polymer parts are successfully made and thus the application area of PCB micro-drilling is broadened.

Journal

Circuit WorldEmerald Publishing

Published: May 5, 2015

There are no references for this article.