Get 20M+ Full-Text Papers For Less Than $1.50/day. Start a 14-Day Trial for You or Your Team.

Learn More →

Eliminating short switching cycles when using hysteresis control of resistance spot welding systems

Eliminating short switching cycles when using hysteresis control of resistance spot welding systems PurposeThis paper aims to present two hysteresis-control algorithms designed for medium-frequency, direct-current, resistance-spot-welding (MFDC RSW) systems. The first proposed control algorithm (MSCHC) eliminates the short switching cycles that can occur when using the existing hysteresis-control algorithms. This control minimises the number of switching cycles that are needed to generate the selected welding current. The welding-current ripple can be high when using this control algorithm. Therefore, a second algorithm (HCRR) is presented that reduces the welding-current ripple by half.Design/methodology/approachThe proposed hysteresis controllers consist of the transformer’s magnetic-flux-density hysteresis regulator and a welding-current hysteresis regulator. Therefore, the welding current must be measured and the saturation of the iron core must be detected. The proposed hysteresis controller supplies the inverter with the signals needed to generate the supply voltage for the RSW transformer, which then generates the selected welding current.FindingsThe proposed MSCHC algorithm produces the smallest possible number of switching cycles needed to generate the selected welding current. The high welding-current ripple can be reduced if the number of switching cycles is increased. The observed number of switching cycles and the welding-current ripple change if the welding resistance and/or inductance change.Originality/valueThe number of switching cycles can be minimised when using the first proposed control algorithm (MSCHC), and so the switching power losses can be minimised. If the welding-current ripple produced by the first control algorithm is unacceptable, the second control algorithm (HCRR) can reduce it by increasing the number of switching cycles. http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.png COMPEL: Theinternational Journal for Computation and Mathematics in Electrical and Electronic Engineering Emerald Publishing

Eliminating short switching cycles when using hysteresis control of resistance spot welding systems

Download PDF
13 pages

Loading next page...
 
/lp/emerald-publishing/eliminating-short-switching-cycles-when-using-hysteresis-control-of-So3YFb6iq0
Publisher
Emerald Publishing
Copyright
Copyright © Emerald Group Publishing Limited
ISSN
0332-1649
DOI
10.1108/COMPEL-09-2016-0429
Publisher site
See Article on Publisher Site

Abstract

PurposeThis paper aims to present two hysteresis-control algorithms designed for medium-frequency, direct-current, resistance-spot-welding (MFDC RSW) systems. The first proposed control algorithm (MSCHC) eliminates the short switching cycles that can occur when using the existing hysteresis-control algorithms. This control minimises the number of switching cycles that are needed to generate the selected welding current. The welding-current ripple can be high when using this control algorithm. Therefore, a second algorithm (HCRR) is presented that reduces the welding-current ripple by half.Design/methodology/approachThe proposed hysteresis controllers consist of the transformer’s magnetic-flux-density hysteresis regulator and a welding-current hysteresis regulator. Therefore, the welding current must be measured and the saturation of the iron core must be detected. The proposed hysteresis controller supplies the inverter with the signals needed to generate the supply voltage for the RSW transformer, which then generates the selected welding current.FindingsThe proposed MSCHC algorithm produces the smallest possible number of switching cycles needed to generate the selected welding current. The high welding-current ripple can be reduced if the number of switching cycles is increased. The observed number of switching cycles and the welding-current ripple change if the welding resistance and/or inductance change.Originality/valueThe number of switching cycles can be minimised when using the first proposed control algorithm (MSCHC), and so the switching power losses can be minimised. If the welding-current ripple produced by the first control algorithm is unacceptable, the second control algorithm (HCRR) can reduce it by increasing the number of switching cycles.

Journal

COMPEL: Theinternational Journal for Computation and Mathematics in Electrical and Electronic Engineering – Emerald Publishing

Published: May 2, 2017

References

  • A comparison of AC and DC current in the resistance spot welding of automotive steels
  • A dead-beat adaptive hysteresis current control