Get 20M+ Full-Text Papers For Less Than $1.50/day. Start a 14-Day Trial for You or Your Team.

Learn More →

Bossed diaphragm coupled fixed guided beam structure for MEMS based piezoresistive pressure sensor

Bossed diaphragm coupled fixed guided beam structure for MEMS based piezoresistive pressure sensor Structures play a very important role in developing pressure sensors with good sensitivity and linearity, as they undergo deformation to the input pressure and function as the primary sensing element of the sensor. To achieve high sensitivity, thinner diaphragms are required; however, excessively thin diaphragms may induce large deflection and instability, leading to the unfavorable performances of a sensor in terms of linearity and repeatability. Thereby, importance is given to the development of innovative structures that offer good linearity and sensitivity. This paper aims to investigate the sensitivity of a bossed diaphragm coupled fixed guided beam three-dimensional (3D) structure for pressure sensor applications.Design/methodology/approachThe proposed sensor comprises of mainly two sensing elements: the first being the 3D mechanical structure made of bulk silicon consisting of boss square diaphragm along with a fixed guided beam landing on to its center, forming the primary sensing element, and the diffused piezoresistors, which form the secondary sensing element, are embedded in the tensile and compression regions of the fixed guided beam. This micro mechanical 3 D structure is packaged for applying input pressure to the bottom of boss diaphragm. The sensor without pressure load has no deflection of the diaphragm; hence, no strain is observed on the fixed guided beam and also there is no change in the output voltage. When an input pressure P is applied through the pressure port, there is a deformation in the diaphragm causing a deflection, which displaces the mass and the fixed guided beam vertically, causing strain on the fixed guided beam, with tensile strain toward the guided end and compressive strain toward the fixed end of the close magnitudes. The geometrical dimensions of the structure, such as the diaphragm, boss and fixed guided beam, are optimized for linearity and maximum strain for an applied input pressure range of 0 to 10 bar. The structure is also analyzed analytically, numerically and experimentally, and the results are compared.FindingsThe structure offers equal magnitudes of tensile and compressive stresses on the surface of the fixed guided beam. It also offers good linearity and sensitivity. The analytical, simulation and experimental studies of this sensor are introduced and the results correlate with each other. Customized process steps are followed wherein two silicon-on-insulator (SOI) wafers are fusion bonded together, with SOI-1 wafer used to realize the diaphragm along with the boss and SOI-2 wafer to realize the fixed guided beam, leading to formation of a 3D structure. The geometrical dimensions of the structure, such as the diaphragm, boss and fixed guided beam, are optimized for linearity and maximum strain for an applied input pressure range of 0 to10 bar.Originality/valueThis paper presents a unique and compact 3D micro-mechanical structure pressure sensor with a rigid center square diaphragm (boss diaphragm) and a fixed guided beam landing at its center, with diffused piezoresistors embedded in the tensile and compression regions of the fixed guided beam. A total of six masks were involved to realize and fabricate the 3D structure and the sensor, which is presumed to be the first of its kind in the fabrication of MEMS-based piezoresistive pressure sensor. http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.png Sensor Review Emerald Publishing

Bossed diaphragm coupled fixed guided beam structure for MEMS based piezoresistive pressure sensor

Download PDF
12 pages

Loading next page...
 
/lp/emerald-publishing/bossed-diaphragm-coupled-fixed-guided-beam-structure-for-mems-based-qmNM3TCE6h
Publisher
Emerald Publishing
Copyright
© Emerald Publishing Limited
ISSN
0260-2288
DOI
10.1108/sr-10-2018-0275
Publisher site
See Article on Publisher Site

Abstract

Structures play a very important role in developing pressure sensors with good sensitivity and linearity, as they undergo deformation to the input pressure and function as the primary sensing element of the sensor. To achieve high sensitivity, thinner diaphragms are required; however, excessively thin diaphragms may induce large deflection and instability, leading to the unfavorable performances of a sensor in terms of linearity and repeatability. Thereby, importance is given to the development of innovative structures that offer good linearity and sensitivity. This paper aims to investigate the sensitivity of a bossed diaphragm coupled fixed guided beam three-dimensional (3D) structure for pressure sensor applications.Design/methodology/approachThe proposed sensor comprises of mainly two sensing elements: the first being the 3D mechanical structure made of bulk silicon consisting of boss square diaphragm along with a fixed guided beam landing on to its center, forming the primary sensing element, and the diffused piezoresistors, which form the secondary sensing element, are embedded in the tensile and compression regions of the fixed guided beam. This micro mechanical 3 D structure is packaged for applying input pressure to the bottom of boss diaphragm. The sensor without pressure load has no deflection of the diaphragm; hence, no strain is observed on the fixed guided beam and also there is no change in the output voltage. When an input pressure P is applied through the pressure port, there is a deformation in the diaphragm causing a deflection, which displaces the mass and the fixed guided beam vertically, causing strain on the fixed guided beam, with tensile strain toward the guided end and compressive strain toward the fixed end of the close magnitudes. The geometrical dimensions of the structure, such as the diaphragm, boss and fixed guided beam, are optimized for linearity and maximum strain for an applied input pressure range of 0 to 10 bar. The structure is also analyzed analytically, numerically and experimentally, and the results are compared.FindingsThe structure offers equal magnitudes of tensile and compressive stresses on the surface of the fixed guided beam. It also offers good linearity and sensitivity. The analytical, simulation and experimental studies of this sensor are introduced and the results correlate with each other. Customized process steps are followed wherein two silicon-on-insulator (SOI) wafers are fusion bonded together, with SOI-1 wafer used to realize the diaphragm along with the boss and SOI-2 wafer to realize the fixed guided beam, leading to formation of a 3D structure. The geometrical dimensions of the structure, such as the diaphragm, boss and fixed guided beam, are optimized for linearity and maximum strain for an applied input pressure range of 0 to10 bar.Originality/valueThis paper presents a unique and compact 3D micro-mechanical structure pressure sensor with a rigid center square diaphragm (boss diaphragm) and a fixed guided beam landing at its center, with diffused piezoresistors embedded in the tensile and compression regions of the fixed guided beam. A total of six masks were involved to realize and fabricate the 3D structure and the sensor, which is presumed to be the first of its kind in the fabrication of MEMS-based piezoresistive pressure sensor.

Journal

Sensor Review – Emerald Publishing

Published: Jul 26, 2019

Keywords: MEMS; Piezoresistive; Pressure sensor; Fixed guided beam; Boss diaphragm

References

  • Fabrication and performance of MEMS-based pressure sensor packages using patterned ultra-thick photoresists
    Chen, L.-T.; Chang, J.-S.; Hsu, C.-Y.; Cheng, W.-H.
  • Novel designs for application specific MEMS pressure sensors
    Fragiacomo, G.; Reck, K.; Lorenzen, L.; Thomsen, E.V.
  • A high sensitivity and high linearity pressure sensor based on a peninsula-structured diaphragm for low-pressure ranges
    Huang, X.; Zhang, D.
  • Polysilicon thin film piezoresistive pressure microsensor: design, fabrication and characterization
    Kumar, S.; Pant, B.D.
  • Process optimization for monolithic integration of piezoresistive pressure sensor and MOSFET amplifier with SOI approach
    Kumar, V.; Dasgupta, A.; Bhat, K.N.
  • The design of a novel structural four-beams-bossed membrane (FBBM) piezoresistive pressure sensor
    Li, C.; Cordovilla, F.; Ocana, J.L.
  • Design optimization and fabrication of a novel structural SOI piezoresistive pressure sensor with high accuracy
    Li, C.; Cordovilla, F.; Jagdheesh, R.; Ocana, J.L.
  • Design, fabrication and testing of fiber bragg grating based fixed guided beam pressure sensor
    Manuvinakurake, M.; Gandhi, U.; Mangalanathan, U.; Nayak, M.
  • The design and optimization of a highly sensitive and overload-resistant piezoresistive pressure sensor
    Meng, X.; Zhao, Y.
  • Piezoelectric microresonant pressure sensor using aluminium nitride
    Sujan, Y.; Uma, G.; Umapathy, M.
  • Center embossed diaphragm design guidelines and Fabry–Perot diaphragm fiber optic sensor
    Sun, Y.; Feng, G.; Georgiou, G.; Niver, E.; Noe, K.; Chin, K.
  • The design and analysis of beam-membrane structure sensors for micro-pressure measurement
    Tian, B.Y.; Zhao, Z.; Jiang, B.; Hu
  • Fabrication and structural design of micro pressure sensors for tire pressure measurement systems (TPMS)
    Tian, B.Y.; Zhao, Z.; Jiang, L.; Zhang, N.; Liao, Y.; Liu, H.; Meng
  • Design, fabrication and characterization of a high-sensitivity pressure sensor based on nano-polysilicon thin film transistors
    Zhao, X.F.; Yu, Y.; Li, D.; Wen, D.
  • Incorporation of beams into bossed diaphragm for a high sensitivity and overload micro pressure sensor
    Yu, Z.; Zhao, Y.; Sun, L.; Tian, B.; Jiang, Z.
  • Realization of a micro pressure sensor with high sensitivity and overload by introducing beams and islands
    Yu, Z.; Zhao, Y.; Li, L.; Li, C.; Liu, Y.; Bian, T.