Residual properties of alkali-activated slag concrete exposed to elevated temperaturesKumar, Virendra; Paswan, Rajesh Kumar
2023 Journal of Structural Fire Engineering
doi: 10.1108/jsfe-05-2021-0021
This paper attempted to study the alkali-activated (AA) binder consisting of 94% of ground granulated blast furnace slag (GGBFS) and 6% of blended powder of alkali metal hydroxide and metal sulfate, which acted as an activator.Design/methodology/approachSeveral concrete specimens (cubes, cylinders and prisms), which were casted using AA binders, were further tested for mechanical properties after exposure to elevated temperatures of 200 °C, 400 °C, 600 °C and 800 °C. Additionally, to understand the structural behavior in uniaxial compressive load, reinforced concrete short columns were cast, cured and tested at ambient temperature as well as after exposure to 300 °C, 600 °C and 900 °C, to know the residual strength after exposure to elevated temperature.FindingsThe findings for the residual strength of alkali-activated slag binder concrete (AASBC) indicated a substantial agreement with the results obtained for the residual strength of Portland slag cement (PSC) concrete, thereby showing the effectiveness of binder when used as a replacement of cement.Originality/valueThe study clearly indicates that the binder developed is an effective approach for the 100% replacement of cement in the concrete.
Behaviour of thin flush end-plate connections in a 3D bare steel frame under fire loading: experimental studyKhonsari, Seyed Vahid; Nejati, Shahin; Rahdan, Mohammadreza; Ahmadi, Mahdi
2023 Journal of Structural Fire Engineering
doi: 10.1108/jsfe-08-2021-0050
The paper aims to report a fire test conducted on a three-dimensional frame in order to investigate the behaviour of bare steel flush end-plate connections with relatively low thickness at elevated temperatures.Design/methodology/approachA half-scale model was fabricated and exposed to modified (scaled) ISO 834 heating curve using a semi-open furnace. The maximum temperature inside the furnace reached 1,026 °C.FindingsThe rotations of connections are reported and compared with those of a previous study on an exactly the same model with thick end-plates. Various modes of failure such as local buckling of the beams flanges and lateral-torsional buckling of beams were observed during the test. Finally, the structure collapsed after 29 min of heating due to the fracture of weld between one of the beams and one of its attached end-plates whilst the other beam had undergone a maximum deflection of 35 cm (≈ 1/6 span length). Other observed failure modes included bolt fracture, bolt thread stripping and large inelastic deformation of the end-plates.Originality/valueAlthough the adoption of thin end-plates increased the rotational capacity of the connections, it did not improve the robustness of the structure under fire conditions.
Tension stiffening model for the finite element analysis of composite floor systems exposed to fireMartinez, Jason; Jeffers, Ann
2023 Journal of Structural Fire Engineering
doi: 10.1108/jsfe-10-2021-0065
A methodology for producing an elevated-temperature tension stiffening model is presented.Design/methodology/approachThe energy-based stress–strain model of plain concrete developed by Bažant and Oh (1983) was extended to the elevated-temperature domain by developing an analytical formulation for the temperature-dependence of the fracture energy Gf. Then, an elevated-temperature tension stiffening model was developed based on the modification of the proposed elevated-temperature tension softening model.FindingsThe proposed tension stiffening model can be used to predict the response of composite floor slabs exposed to fire with great accuracy, provided that the global parameters TS and Kres are adequately calibrated against global structural response data.Originality/valueIn a finite element analysis of reinforced concrete, a tension stiffening model is required as input for concrete to account for actions such as bond slip and tension stiffening. However, an elevated-temperature tension stiffening model does not exist in the research literature. An approach for developing an elevated-temperature tension stiffening model is presented.
Some recent developments and testing strategies relating to the passive fire protection of concrete using intumescent coatings: a reviewGhiji, Matt; Joseph, Paul; Guerrieri, Maurice
2023 Journal of Structural Fire Engineering
doi: 10.1108/jsfe-11-2021-0069
In the present article, the authors have conducted a review on some of the recent developments given in the literature pertaining to the passive protection of concrete structures using intumescent coatings. Here, the main thrust is placed on the spalling phenomenon of concrete elements when exposed to elevated temperatures and fires.Design/methodology/approachIn this context, it has been long established that prolonged thermal insult on concrete members will lead to egress of water, both physically bound as well as those present as water of hydration within the concrete matrix, in the form of steam through microchannels and associated pathways of least resistance, often resulting in the flaking of the surface of the structure. The latter process can ultimately lead to the exposure of the ferrous-based reenforcement elements, for instance, to higher temperatures, thus inducing melting. This, in turn, can result in substantial loss of strength and load-bearing capacity of the structural element that is already undergoing disintegration of its base matrix owing to heat/fire. Even though spalling of concrete structures has long been recognized as a serious problem that can often lead to catastrophic failure of infrastructures, such as buildings, bridges and tunnels, the utility of intumescent coating as a mitigation strategy is relatively new and has not been explored to its fullest possible extent. Therefore, in the latter parts of the review, the authors have endeavored to discuss the different types of intumescent coatings, their modes of actions and, in particular, their wider applicability in terms of protecting concrete elements from detrimental effects of severe or explosive spalling.FindingsGiven that spalling of concrete components is still a very serious issue that can result in loss of lives and destruction of critical infrastructures, there is an urgent need to formulate better mitigating strategies, through novel means and methods. The use of the intumescent coating in this context appears to be a promising way forward but is one that seems to be little explored so far. Therefore, a more systematic investigation is highly warranted in this area, especially, as the authors envisage a greater activity in the building and commissioning of more infrastructures worldwide incommensurate with augmented economic activities during the post-COVID recovery period.Originality/valueThe authors have conducted a review on some of the recent developments given in the literature pertaining to the passive protection of concrete structures using intumescent coatings. The authors have also included the results from some recent tests carried out at the facilities using a newly commissioned state-of-the-art furnace.
Proposal of steel stress-strain relationships and simple analytical models of beams considering strain-rate effects at elevated temperaturesOzaki, Fuminobu; Umemura, Takumi
2023 Journal of Structural Fire Engineering
doi: 10.1108/jsfe-01-2022-0001
In this study, engineering stress-strain relationships considering an effect of strain rate on steel materials at elevated temperatures were formulated and a simplified analytical model using a two-dimensional beam element to analytically examine the effect of strain rate on the load-bearing capacity and collapse temperature was proposed.Design/methodology/approachThe stress-strain relationships taking into account temperature, strain, and strain rate were established based on the past coupon test results with strain rate as the test parameter. Furthermore, an elasto-plastic analysis using a two-dimensional beam element, which considered the effect on strain rate, was conducted for both transient- and steady-state conditions.FindingsThe analytical results agreed relatively well with the test results, which used small steel beam specimens with a rectangular cross-section under various heating rates (transient-state condition) and deformation rates (steady-state condition). It was found that the bending strength and collapse temperature obtained from the parametric analyses agreed relatively well with those evaluated using the effective strength obtained from the coupon tests with strain equal to 0.01 or 0.02 under the fast strain rates.Originality/valueThe effect of stress degradation, including the stress-strain relationships at elevated temperature, was mitigated by considering the effect of strain rate on the analytical model. This is an important point to consider when considering the effect of strain rate on steel structural analysis at elevated temperatures to maintain analytical stability unaccompanied by the stress degradation.
Behavior of hot-dip zinc-aluminum coated steel under elevated temperature in case of firePinger, Thomas; Mensinger, Martin; Firan, Maria-Mirabela
2023 Journal of Structural Fire Engineering
doi: 10.1108/jsfe-02-2022-0005
Based on the advantages of conventional hot-dip galvanizing made from quasi-pure zinc melts in the event of fire, this article aims to perform a series of tests to verify whether a similar effect can be achieved with zinc-aluminum coatings.Design/methodology/approachThe emissivity of galvanized surfaces, which were applied to steel specimens by the batch hot-dip galvanizing process, was experimentally determined under continuously increasing temperature load. In addition to a quasi-pure zinc melt serving as a reference, a zinc melt alloyed with 500 ppm aluminum and thin-film galvanized with a melt of zinc and 5% aluminum were used. For the latter, variants of post-treatment measures in terms of a passivation and sealing of the galvanizing were also investigated.FindingsThe results show that lower emissivity can be achieved at higher temperatures by adding aluminum to the zinc melt and thereby into the zinc coating. The design values required for the structural fire design were proposed, and an exemplary calculation of the temperature development in the case of fire was carried out based on the values. The result of this calculation indicates that the savings potential becomes apparent, when using zinc-aluminum coatings.Originality/valueThe presented novel tests describe the behavior of zinc-aluminum coatings under the influence of elevated temperatures and their positive effect on the emissivity of steel components galvanized by this method. The results provide valuable insights and information on the performance in the event of fire and the associated potential savings for steel construction.
Modelling concrete slabs subjected to localised fire action with OpenSeesOrabi, Mhd Anwar; Qiu, Jin; Jiang, Liming; Usmani, Asif
2023 Journal of Structural Fire Engineering
doi: 10.1108/jsfe-05-2021-0033
Reinforced concrete slabs in fire have been heavily studied over the last three decades. However, most experimental and numerical work focuses on long-duration uniform exposure to standard fire. Considerably less effort has been put into investigating the response to localised fires that result in planarly non-uniform temperature distribution in the exposed elements.Design/methodology/approachIn this paper, the OpenSees for Fire framework for modelling slabs under non-uniform fire exposure is presented, verified against numerical predictions by Abaqus and then validated against experimental tests. The thermal wrapper developed within OpenSees for Fire is then utilised to apply localised fire exposure to the validated slab models using the parameters of an experimentally observed localised fire. The effect of the smoke layer is also considered in this model and shown to significantly contribute to the thermal and thus thermo-mechanical response of slabs. Finally, the effect of localised fire heat release rate (HRR) and boundary conditions are studied.FindingsThe analysis showed that boundary conditions are very important for the response of slabs subject to localised fire, and expansive strains may be accommodated as deflections without severely damaging the slab by considering the lateral restraint.Originality/valueThis work demonstrates the capabilities of OpenSees for Fire in modelling structural behaviours subjected to non-uniform fire conditions and investigates the damage pattens of flat slabs exposed to localised fires. It is an advancing step towards understanding structural responses to realistic fires.