Get 20M+ Full-Text Papers For Less Than $1.50/day. Start a 14-Day Trial for You or Your Team.

Learn More →

The Overall Effects of AlN Nanoparticle Addition to Hybrid Magnesium Alloy AZ91/ZK60A

The Overall Effects of AlN Nanoparticle Addition to Hybrid Magnesium Alloy AZ91/ZK60A The Overall Effects of AlN Nanoparticle Addition to Hybrid Magnesium Alloy AZ91/ZK60A Hindawi Publishing Corporation Home Journals About Us About this Journal Submit a Manuscript Table of Contents Journal Menu Abstracting and Indexing Aims and Scope Annual Issues Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Reviewers Acknowledgment Subscription Information Open Special Issues Published Special Issues Special Issue Guidelines Abstract Full-Text PDF Full-Text HTML Full-Text ePUB Linked References How to Cite this Article Complete Special Issue Journal of Nanotechnology Volume 2012 (2012), Article ID 687306, 8 pages doi:10.1155/2012/687306 Research Article The Overall Effects of AlN Nanoparticle Addition to Hybrid Magnesium Alloy AZ91/ZK60A Muralidharan Paramsothy , 1 Jimmy Chan , 2 Richard Kwok , 2 and Manoj Gupta 1 1 Department of Mechanical Engineering, National University of Singapore, 9 Engineering Drive 1, 117576, Singapore 2 CTO Office, Singapore Technologies Kinetics Ltd (ST Kinetics), 249 Jalan Boon Lay, 619523, Singapore Received 5 December 2011; Accepted 11 February 2012 Academic Editor: Hongmei Luo Copyright © 2012 Muralidharan Paramsothy et al. This is an open access article distributed under the Creative Commons Attribution License , which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Abstract A hybrid magnesium alloy nanocomposite containing AlN nanoparticle reinforcement was fabricated using solidification processing followed by hot extrusion. The nanocomposite exhibited similar grain size to the monolithic hybrid alloy, reasonable AlN and intermetallic nanoparticle distribution, nondominant ( 0 0 0 2 ) texture in the longitudinal direction, and 17% higher hardness than the monolithic hybrid alloy. Compared to the monolithic hybrid alloy, the nanocomposite exhibited higher tensile yield strength (0.2% TYS) and ultimate tensile strength (UTS) without significant compromise in failure strain and energy absorbed until fracture (EA) (+5%, +5%, −14% and −10%, resp.). Compared to the monolithic hybrid alloy, the nanocomposite exhibited unchanged compressive yield strength (0.2% CYS) and higher ultimate compressive strength (UCS), failure strain, and EA (+1%, +6%, +24%, and +6%, resp.). The overall effects of AlN nanoparticle addition on the tensile and compressive properties of the hybrid magnesium alloy is investigated in this paper. 1. Introduction Compared to aluminium, magnesium is the lightest structural metal (35% lighter) used in many engineering applications today [ 1 , 2 ]. Commercially available magnesium alloys are suitable for actual or potential use regarding weight-critical applications in the automotive, aerospace, civil infrastructure, building and construction, defence, biomedical, and sports/recreational industries [ 1 , 3 ]. In the World War 2 era, Mg-Zn alloy parts were economically manufactured and heavily used in aircraft [ 3 ]. Soon after the world war, Mg-Al alloys were also economically developed with specific metallurgical advantages over Mg-Zn alloys [ 3 ]. At present, Mg-Y and Mg-RE (Rare Earth) alloys are in development for even more specific metallurgical advantages but at generally higher cost compared to Mg-Zn and Mg-Al alloys [ 1 ]. Regardless of cast or wrought forms, Mg-Zn and Mg-Al alloys each still remain as the main classes of Mg alloys commercially in use. In the wrought form, the Mg alloys have good strength and ductility. However, wrought Mg-Zn and Mg-Al alloy nanocomposites have often demonstrated simultaneously higher strength and ductility compared to the monolithic alloys [ 4 – 14 ]. Additionally, friction stir processed Mg-Al nanocomposites have also demonstrated higher hardness and strength than the corresponding monolithic alloys [ 15 – 18 ]. Based on much of the existing representative research literature on solidification processed magnesium alloy nanocomposites, good nanoparticle distribution can be achieved in the magnesium matrix and better mechanical properties can be achieved due to the addition of nanoparticles [ 4 – 18 ]. However, it is the addition of oxide- or carbon-based nanoparticles to magnesium alloys as opposed to nitride-based nanoparticle addition that most of the research literature currently discusses. In the context of magnesium composite processing, the magnesium-oxygen strong affinity and magnesium-carbon weak affinity (comparative to each other) are both well known. On the other hand, what is not known is the affinity between magnesium and nitrogen concerning effects in magnesium nanocomposite processing (let alone solidification processing). Accordingly, one of the primary aims of this study was to simultaneously increase tensile strength and ductility of AZ91/ZK60A hybrid magnesium alloy with AlN nanoparticles. Another aim of the present study was to evaluate the compressive properties of AZ91/ZK60A/AlN hybrid alloy nanocomposite. Disintegrated melt deposition (DMD) [ 19 , 20 ] followed by hot extrusion was used to synthesize the AZ91/ZK60A/AlN hybrid alloy nanocomposite. 2. Experimental Procedures 2.1. Materials In this study, AZ91 (nominally 8.30–9.70 wt.% Al, 0.35–1.00 wt.% Zn, 0.15–0.50 wt.% Mn, 0.10 wt.% Si, 0.030 wt.% Cu, 0.005 wt.% Fe, 0.002 wt.% Ni, 0.02 wt.% others, balance Mg) and ZK60A (nominally 4.80–6.20 wt.% Zn, 0.45 wt.% Zr, balance Mg), both alloys supplied by Tokyo Magnesium Co. Ltd. (Yokohama, Japan) were used as matrix material. 3 parts AZ91 were mixed with 1 part ZK60A by mass to metallurgically downgrade AZ91. The intention of this mixing was to decrease the nominal aluminium content of AZ91 by 2 wt.%. AZ91 and ZK60A blocks were sectioned to smaller pieces. All oxide and scale surfaces were removed using machining. All surfaces were washed with ethanol after machining. AlN nanoparticles (99% purity, spherical, 10–20 nm size) supplied by Nanostructured & Amorphous Materials Inc (TX, USA) were used as the reinforcement phase. 2.2. Processing Monolithic AZ91/ZK60A hybrid alloy (nominal aluminium content of AZ91 decreased by 2 wt.%.) was cast using the DMD method [ 19 , 20 ]. This involved heating AZ91 and ZK60A blocks to 750°C in an inert Ar gas atmosphere in a graphite crucible (A12 designated size of top OD: 171 mm, bottom OD: 121 mm, height: 210 mm) using a resistance heating furnace. The crucible was equipped with an arrangement for bottom pouring. Upon reaching the superheat temperature, the molten slurry was stirred for 2.5 min at 460 rpm using a twin blade (pitch 45°) mild steel impeller to facilitate the uniform distribution of heat. The impeller was coated with Zirtex 25 (86% ZrO 2 , 8.8% Y 2 O 3 , 3.6% SiO 2 , 1.2% K 2 O and Na 2 O, and 0.3% trace inorganics) to avoid iron contamination of the molten metal. The melt was then released through a 10 mm diameter orifice at the base of the crucible. The melt was disintegrated by two jets of argon gas oriented normal to the melt stream located 265 mm from the melt pouring point. The argon gas flow rate was maintained at 25 lpm. The disintegrated melt slurry was subsequently deposited onto a metallic substrate located 500 mm from the disintegration point. An ingot of 40 mm diameter was obtained following the deposition stage. To form the AZ91/ZK60A/1.5 vol% AlN hybrid alloy nanocomposite, AlN nanoparticle powder was isolated by wrapping in Al foil of minimal weight (<0.50 wt.% with respect to AZ91 and ZK60A total matrix weight) and arranged on top of the AZ91 and ZK60A alloy blocks (see Figure 1 ), with all other DMD parameters unchanged. All billets were machined to 35 mm diameter and hot-extruded using 20.25 : 1 extrusion ratio on a 150 ton hydraulic press. The extrusion temperature was 350°C. The billets were held at 400°C for 60 min in a furnace prior to extrusion. Colloidal graphite was used as a lubricant. Rods of 8 mm were obtained. Figure 1: Arrangement of raw materials in crucible before casting for AZ91/ZK60A/AlN nanocomposite. 2.3. Heat Treatment Heat treatment was carried out on all extruded sections at 200°C for 1 hour using a resistance heating furnace. This selection of temperature and time was made in order to relax the monolithic AZ91/ZK60A hybrid alloy (nominal aluminium content of AZ91 decreased by 2 wt.%.) without recrystallization softening. The recrystallization temperature of AZ61 magnesium alloy (as the nearest matching alloy in terms of composition) following 20% cold work after 1 hour is 288°C [ 1 ]. Prior to heat treatment, the sections were coated with colloidal graphite and wrapped in aluminum foil to minimize reaction with oxygen present in the furnace atmosphere. 2.4. Microstructural Characterization Microstructural characterization studies were conducted on metallographically polished monolithic and nanocomposite extruded samples to determine grain characteristics. Hitachi S4300 Field-Emission SEM (FESEM) was used. Image analysis using Scion software was carried out to determine the grain characteristics. Thin foils were prepared from the monolithic and nanocomposite extruded samples for transmission electron microscopy (TEM) using disc punch-out and ion-milling for nanoparticle distribution observation (regarding localized effects). Goniometer XRD studies were conducted using CuK α radiation ( 𝜆 = 1 . 5 4 0 6 Å ) with a scan speed of 2°/min in an automated Shimadzu LAB-X XRD-6000 diffractometer to determine intermetallic phase(s) presence and dominant textures in the transverse and longitudinal (extrusion) directions (regarding globalised effects). 2.5. Hardness Microhardness measurements were made on polished monolithic and nanocomposite extruded samples. Vickers microhardness was measured with an automatic digital Shimadzu HMV Microhardness Tester using 25 gf-indenting load and 15 s dwell time. 2.6. Tensile Testing Smooth bar tensile properties of the monolithic and nanocomposite extruded samples were determined based on ASTM E8M-05. Round tension test samples of 5 mm diameter and 25 mm gauge length were subjected to tension using an MTS 810 machine equipped with an axial extensometer with a crosshead speed set at 0.254 mm/min. 2.7. Compressive Testing Compressive properties of the monolithic and nanocomposite extruded samples were determined based on ASTM E9-89a. Samples of 8 mm length ( 𝑙 ) and 8 mm diameter ( 𝑑 ) where 𝑙 / 𝑑 = 1 were subjected to compression using a MTS 810 machine with 0.005 min −1 strain rate. 3. Results 3.1. Macrostructural Characteristics No macropores or shrinkage cavities were observed in the cast monolithic and nanocomposite materials. No macrostructural defects were observed for extruded rods of monolithic and nanocomposite materials. 3.2. Microstructural Characteristics Microstructural analysis results revealed that grain size and aspect ratio remained statistically unchanged in the case of nanocomposite as shown in Table 1 and Figures 2(a) and 2(b) . Grain size refers to diameter of the grain assuming it is circular in shape. AlN nanoparticle reinforcement and fine intermetallic particle distributions in the nanocomposite were reasonably uniform as shown in Figure 2(c) . Table 1: Results of grain characteristics and microhardness of AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite. Figure 2: Representative FESEM micrographs showing grain size in monolithic AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite: (a) lower magnification and (b) higher magnification. (c) Representative TEM micrograph (including SAED pattern) showing the presence of individual nitride nanoparticles and fine intermetallic particles in AZ91/ZK60A/AlN nanocomposite. (d) Representative TEM micrograph (including SAED pattern) showing the presence of individual Mg-Zn rod-shaped nanoparticles in AZ91/ZK60A/AlN nanocomposite. Phases present but not labeled in the SAED patterns include Mg and Mg-Al phases only. Texture results are listed in Table 2 and shown in Figure 3 . In monolithic and nanocomposite materials, the dominant texture in the transverse and longitudinal directions was ( 1 0 − 1 1 ) . Here, extrusion did not result in the ( 0 0 0 2 ) plane being intensely parallel to the extrusion direction (as we have previously reported) [ 6 – 14 ]. Table 2: Texture results of AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite based on goniometer X-ray diffraction. Figure 3: Schematic diagram showing textures of monolithic AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite based on goniometer X-ray diffraction. In each case, vertical axis (dotted line) is parallel to extrusion direction. Each cell is made up of 2 HCP units having 1 common ( 0 0 0 2 ) basal splane. 3.3. Hardness The results of microhardness measurements are listed in Table 1 . The nanocomposite exhibited higher hardness than the monolithic material. 3.4. Tensile Behavior The overall results of ambient temperature tensile testing of the extruded materials are shown in Table 3 and Figure 4(a) . The strength of AZ91/ZK60A/1.5 vol% AlN was higher compared to monolithic AZ91/ZK60A, without significant compromise in failure strain and energy absorbed until fracture (EA). EA was determined by computing the area under the stress-strain curve up to the point of fracture. Table 3: Results of tensile testing of AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite. Figure 4: Representative: (a) tensile and (b) compressive stress-strain curves of monolithic AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite. 3.5. Compressive Behavior The overall results of ambient temperature compressive testing of the extruded materials are shown in Table 4 and Figure 4(b) . Comparing AZ91/ZK60A/1.5 vol% AlN to monolithic AZ91/ZK60A, yield strength was unchanged and ultimate strength, failure strain, and EA were each higher. Table 4: Results of compressive testing of AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite. 4. Discussion 4.1. Synthesis of Monolithic AZ91/ZK60A and AZ91/ZK60A/AlN Nanocomposite Synthesis of monolithic and nanocomposite materials, the final form being extruded rods, was successfully accomplished with no detectable metal oxidation or reaction between graphite crucible and melts. The inert atmosphere used during DMD was effective in preventing oxidation of the Mg melt. No stable carbides of Mg or Al formed due to reaction with graphite crucible. 4.2. Microstructural Characteristics Microstructural characterization of extruded samples is discussed in terms of (a) grain characteristics and (b) AlN and intermetallic nanoparticle reinforcement distribution. Nearly equiaxed grains were observed in monolithic material and nanocomposite as shown in Table 1 and Figures 2(a) and 2(b) . Grain size was statistically unchanged in the case of nanocomposite, suggesting the inability of AlN nanoparticles to serve as either nucleation sites or obstacles to grain growth during solid state cooling. It was observed that Al 12 Mg 17 and Mg 2 Zn 11 intermetallic particles decorated the grain boundaries in the monolithic material and nanocomposite. Goniometer X-ray diffraction (XRD) analysis revealed the presence of Al 12 Mg 17 and Mg 2 Zn 11 phases [ 4 , 11 ]. This was possibly due to near-homogenous (as opposed to total homogenous) mixing of AZ91 and ZK60A constituent alloys since the mixing time at 750°C before spray deposition was only a few minutes. Al 12 Mg 17 and Mg 2 Zn 11 intermetallic phases are commonly found in the individual AZ91 and ZK60A alloys, respectively [ 1 ]. The reasonably uniform distribution of AlN and intermetallic nanoparticles as shown in Figure 2(c) can be attributed to (a) minimal gravity-associated segregation due to judicious selection of stirring parameters [ 21 ], (b) good wetting of AlN nanoparticles by the alloy matrix [ 11 , 22 – 24 ], (c) argon gas disintegration of metallic stream [ 25 ], and (d) dynamic deposition of composite slurry on substrate followed by hot extrusion. In the nanocomposite, selected area electron diffraction (SAED) in TEM revealed the (a) partial reaction of AlN with the Mg alloy matrix to form Mg 3 N 2 (see Figure 2(c) ) and (b) the occurrence of Mg-Zn nanorods (not observed in the monolithic alloy, see Figure 2(d) ). Regarding the occurrence of Mg-Zn nanorods, the Mg-Zn intermetallic phase(s) precipitation was possibly regulated at nanoscale due to the presence of well-dispersed AlN nanoparticles. Dissolved Zn possibly segregated at the liquid-AlN nanoparticle interface enabling Mg-Zn intermetallic phase manipulation at the nanoscale. This is similar to possible dissolved Zn segregation at the liquid-SiC nanoparticle interface enabling nanoscale MgZn 2 precipitation as recently reported [ 26 ]. With a reasonably uniform AlN distribution throughout the AZ91/ZK60A matrix, the nanoparticle-matrix interface area was ample for effectively regulated segregation of 4.80–6.20 wt.% Zn (or 1.21–1.59 vol. % Zn) as nanoscale Mg-Zn precipitates. This was similar to that reported recently for selected ZK60A nanocomposites [ 12 – 14 ]. 4.3. Mechanical Behavior 4.3.1. Hardness A significant increase in microhardness by 17% was observed in the nanocomposite when compared to monolithic material as listed in Table 1 . This was consistent with earlier observations made on Mg/Al 2 O 3 , AZ31/C 60 and AZ31/MWCNT nanocomposites [ 16 , 17 , 27 – 29 ]. The increase in hardness of the nanocomposite in the present study can be attributed to (a) reasonably uniform distribution of harder AlN nanoparticles in the matrix and (b) higher constraint to localized matrix deformation during indentation due to the presence of nanoparticles [ 27 , 28 ]. 4.3.2. Tensile and Compressive Behavior The tensile and compressive strengths of monolithic material and nanocomposite are listed in Tables 3 and 4 (and shown in Figures 4(a) and 4(b) ), respectively. 0.2% TYS and UTS were enhanced by 5% each in AZ91/ZK60A/1.5 vol% AlN compared to monolithic material. In comparison of compressive strengths, 0.2% CYS and UCS of AZ91/ZK60A/1.5 vol% AlN were unchanged and higher by 6%, respectively, compared to monolithic material. However, the compressive stress detected at any given strain was lower for AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A as shown in Figure 4(b) . The tensile strength increase in AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A can be attributed to the following well-known factors (pertaining to reinforcement): (a) dislocation generation due to elastic modulus mismatch and coefficient of thermal expansion mismatch between the matrix and reinforcement [ 28 – 31 ], (b) Orowan strengthening mechanism [ 30 – 32 ], and (c) load transfer from matrix to reinforcement [ 28 , 30 ]. The lower compressive strength of AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A can be attributed possibly to compressive shear buckling of brittle Mg-Zn nanorods in AZ91/ZK60A/1.5 vol% AlN as illustrated in Figure 5 . The compressive shear buckling of Mg-Zn nanorods induces a slightly lower limit on the factors pertaining to reinforcement (as just described). Figure 5: Schematic diagram illustrating compressive shear buckling of brittle Mg-Zn nanorod (circled in TEM micrograph) in AZ91/ZK60A/AlN nanocomposite. 𝜏 𝑎 and 𝜏 𝑏 represent planar shear stresses where 𝜏 𝑎 < 𝜏 𝑏 . 𝜒 (exaggerated) represents very low angular deflection of the brittle Mg-Zn nanorod during buckling. In both AZ91/ZK60A/1.5 vol% AlN and monolithic AZ91/ZK60A, 0.2% TYS was about 2.21 and 2.12 times the 0.2% CYS, respectively. Here, the tensile/compressive yield stress anisotropy (0.2% TYS/0.2% CYS) was present despite the crystallographic texture exhibited where { 1 0 1 − 2 } ⟨ 1 0 1 − 1 ⟩ -type twinning was activated along the 𝑐 -axis of the HCP unit cell in Figure 3 with comparatively similar ease in both tension and compression along the 𝑐 -axis, based on the 45° angle between the 𝑐 -axis and the vertical axis [ 33 , 34 ]. The tensile/compressive yield stress anisotropy (0.2% TYS/0.2% CYS) can be attributed generally to half the strain rate used (less strain hardening) in compressive testing compared to tensile testing. The tensile/compressive yield stress anisotropy was slightly higher for AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A (2.21 compared to 2.12, resp.). This was similar to that observed in the case of selected ZK60A nanocomposites compared to monolithic ZK60A [ 12 – 14 ]. This can be attributed possibly to compressive shear buckling of brittle Mg-Zn nanorods as illustrated in Figure 5 . The brittle Mg-Zn nanorod is prone to buckling followed by fracture within the AZ91/ZK60A matrix during compressive deformation unlike during tensile deformation. The tensile and compressive failure strains of monolithic material and nanocomposite are listed in Tables 3 and 4 (and based on stress-strain curves shown in Figures 4(a) and 4(b) ), respectively. Compared to monolithic material, tensile failure strain was slightly compromised (−14%) in AZ91/ZK60A/1.5 vol% AlN. Compared to monolithic material, compressive failure strain was higher (+24%) in AZ91/ZK60A/1.5 vol% AlN. Both trends in failure strain of AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A can be attributed to the presence of Mg-Zn nanorods (not observed in monolithic AZ91/ZK60A) in AZ91/ZK60A/1.5 vol% AlN (see Figure 2(d) ). Regarding the trend in tensile failure strain, it has been shown in previous studies that the nanoparticles provide sites where cleavage cracks are opened ahead of the advancing crack front. This cleavage crack opening dissipates the stress concentration that would otherwise exist at the crack front and alters the local effective stress state from plane strain to plane stress in the neighbourhood of the crack tip [ 27 , 35 ]. However, stress concentrations around the sharp ends of the Mg-Zn nanorods could not be effectively diffused by the surrounding near-spherical AlN or Mg-Al intermetallic nanoparticles. The trend in tensile failure strain can also be attributed to the partial reactivity between AlN nanoparticles and the Mg alloy matrix where Mg 3 N 2 was formed (see Figure 2(c) ). Regarding the trend in compressive failure strain, compressive shear buckling of Mg-Zn nanorods within the AZ91/ZK60A matrix (see Figure 5 ) aided in dispersing localized stored energy during compressive deformation. This allowed AZ91/ZK60A/1.5 vol% AlN to globally absorb relatively large amounts of strain energy during compressive deformation [ 12 , 36 ]. Here, Mg-Zn nanorod buckling within the AZ91/ZK60A matrix is a compressive toughening mechanism. 5. Conclusions (i) Monolithic AZ91/ZK60A and AZ91/ZK60A/1.5 vol% AlN nanocomposite can be successfully synthesized using the DMD technique followed by hot extrusion. (ii) Compared to monolithic AZ91/ZK60A, tensile strength of AZ91/ZK60A/1.5 vol% AlN was enhanced. This can be attributed to well-known factors pertaining to reinforcement. Compared to monolithic AZ91/ZK60A, compressive strength of AZ91/ZK60A/1.5 vol% AlN was decreased. This can be attributed possibly to compressive shear buckling of Mg-Zn nanorods in the nanocomposite. (iii) Compared to monolithic AZ91/ZK60A, tensile and compressive failure strains of AZ91/ZK60A/1.5 vol% AlN were slightly compromised and enhanced, respectively. The slight compromise in tensile failure strain can be attributed to (a) stress concentrations around the sharp ends of the Mg-Zn nanorods not being effectively diffused by the surrounding near-spherical AlN or Mg-Al intermetallic nanoparticles and (b) partial reactivity between AlN nanoparticles and the Mg alloy matrix where Mg 3 N 2 was formed. The enhancement in compressive failure strain can be attributed to compressive shear buckling of Mg-Zn nanorods in the AZ91/ZK60A matrix. Acknowledgments The authors wish to acknowledge National University of Singapore (NUS) and Temasek Defence Systems Institute (TDSI) for funding this research (TDSI/09-011/1A and WBS no. R265000349). References M. M. Avedesian and H. Baker, ASM Specialty Handbook: Magnesium and Magnesium Alloys , ASM International, Novelty, Ohio, USA, 1999. J. G. Kaufman, Introduction to Aluminium Alloys and Tempers , ASM International, Materials Park, Ohio, USA, 2000. E. F. Emley, Principles of Magnesium Technology , Pergamon Press, Oxford, UK, 1966. M. Paramsothy, S. F. Hassan, N. Srikanth, and M. Gupta, “Enhancing tensile/compressive response of magnesium alloy AZ31 by integrating with Al 2 O 3 nanoparticles,” Materials Science and Engineering A , vol. 527, no. 1-2, pp. 162–168, 2009. View at Publisher · View at Google Scholar · View at Scopus M. Paramsothy, S. F. Hassan, N. Q. Bau, N. Srikanth, and M. Gupta, “Selective enhancement of tensile/compressive strength and ductility of AZ31 magnesium alloy via nano-Al 2 O 3 reinforcement integration method alteration,” Materials Science Forum , vol. 618, pp. 423–427, 2009. View at Publisher · View at Google Scholar · View at Scopus M. Paramsothy, S. F. Hassan, N. Srikanth, and M. Gupta, “Simultaneous enhancement of tensile/compressive strength and ductility of magnesium alloy az31 using carbon nanotubes,” Journal of Nanoscience and Nanotechnology , vol. 10, no. 2, pp. 956–964, 2010. View at Publisher · View at Google Scholar · View at Scopus M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Carbon nanotube addition to simultaneously enhance strength and ductility of hybrid AZ31/AA5083 alloy,” Materials Sciences & Applications , vol. 2, pp. 20–29, 2011. M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “The synergistic ability of Al 2 O 3 nanoparticles to enhance mechanical response of hybrid alloy AZ31/AZ91,” Journal of Alloys and Compounds , vol. 509, no. 28, pp. 7572–7578, 2011. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Enhanced mechanical response of hybrid alloy AZ31/AZ91 based on the addition of Si 3 N 4 nanoparticles,” Materials Science and Engineering A , vol. 528, no. 21, pp. 6545–6551, 2011. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “TiC nanoparticle addition to enhance the mechanical response of hybrid magnesium alloy,” Journal of Nanotechnology , vol. 2012, Article ID 401574, 2012. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “The effective reinforcement of magnesium alloy ZK60A using Al 2 O 3 nanoparticles,” Journal of Nanoparticle Research , vol. 13, no. 10, pp. 4855–4866, 2011. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Addition of CNTs to enhance tensile/compressive response of magnesium alloy ZK60A,” Composites Part A , vol. 42, no. 2, pp. 180–188, 2011. View at Publisher · View at Google Scholar · View at Scopus M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Enhanced mechanical response of magnesium alloy ZK60A containing Si 3 N 4 nanoparticles,” Composites Part A , vol. 42, no. 12, pp. 2093–2100, 2011. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Adding TiC nanoparticles to magnesium alloy ZK60A for strength/ductility enhancement,” Journal of Nanomaterials , vol. 2011, Article ID 642980, 2011. View at Publisher · View at Google Scholar Y. Morisada, H. Fujii, T. Nagaoka, and M. Fukusumi, “Effect of friction stir processing with SiC particles on microstructure and hardness of AZ31,” Materials Science and Engineering A , vol. 433, no. 1-2, pp. 50–54, 2006. View at Publisher · View at Google Scholar · View at Scopus Y. Morisada, H. Fujii, T. Nagaoka, and M. Fukusumi, “Nanocrystallized magnesium alloy—uniform dispersion of C 60 molecules,” Scripta Materialia , vol. 55, no. 11, pp. 1067–1070, 2006. View at Publisher · View at Google Scholar · View at Scopus Y. Morisada, H. Fujii, T. Nagaoka, and M. Fukusumi, “MWCNTs/AZ31 surface composites fabricated by friction stir processing,” Materials Science and Engineering A , vol. 419, no. 1-2, pp. 344–348, 2006. View at Publisher · View at Google Scholar · View at Scopus C. J. Lee, J. C. Huang, and P. J. Hsieh, “Mg based nano-composites fabricated by friction stir processing,” Scripta Materialia , vol. 54, no. 7, pp. 1415–1420, 2006. View at Publisher · View at Google Scholar · View at Scopus L. M. Tham, M. Gupta, and L. Cheng, “Influence of processing parameters during disintegrated melt deposition processing on near net shape synthesis of aluminium based metal matrix composites,” Materials Science and Technology , vol. 15, no. 10, pp. 1139–1146, 1999. View at Scopus M. Gupta, M. O. Lai, and S. C. Lim, “Regarding the processing associated microstructure and mechanical properties improvement of an Al-4.5 Cu alloy,” Journal of Alloys and Compounds , vol. 260, no. 1-2, pp. 250–255, 1997. View at Scopus L. M. Tham, M. Gupta, and L. Cheng, “Influence of processing parameters during disintegrated melt deposition processing on near net shape synthesis of aluminium based metal matrix composites,” Materials Science and Technology , vol. 15, no. 10, pp. 1139–1146, 1999. View at Scopus B. Q. Han and D. C. Dunand, “Microstructure and mechanical properties of magnesium containing high volume fractions of yttria dispersoids,” Materials Science and Engineering A , vol. 277, no. 1-2, pp. 297–304, 2000. View at Scopus N. Eustathopoulos, M. G. Nicholas, and B. Drevet, Wettability at High Temperatures, Vol. 3 , Pergamon Materials Series, Pergamon, New York, NY, USA, 1999. J. D. Gilchrist, Extraction Metallurgy , Pergamon Press, New York, NY, USA, 3rd edition, 1989. M. Gupta, M. O. Lai, and C. Y. Soo, “Effect of type of processing on the micro structural features and mechanical properties of Al-Cu/SiC metal matrix composites,” Materials Science and Engineering A , vol. 210, no. 1-2, pp. 114–122, 1996. View at Scopus M. De Cicco, H. Konishi, G. Cao et al., “Strong, ductile magnesium-zinc nanocomposites,” Metallurgical and Materials Transactions A , vol. 40, no. 12, pp. 3038–3045, 2009. View at Publisher · View at Google Scholar · View at Scopus S. F. Hassan and M. Gupta, “Effect of particulate size of Al 2 O 3 reinforcement on microstructure and mechanical behavior of solidification processed elemental Mg,” Journal of Alloys and Compounds , vol. 419, no. 1-2, pp. 84–90, 2006. View at Publisher · View at Google Scholar · View at Scopus S. F. Hassan and M. Gupta, “Effect of different types of nano-size oxide participates on microstructural and mechanical properties of elemental Mg,” Journal of Materials Science , vol. 41, no. 8, pp. 2229–2236, 2006. View at Publisher · View at Google Scholar · View at Scopus S. F. Hassan and M. Gupta, “Enhancing physical and mechanical properties of Mg using nanosized Al 2 O 3 particulates as reinforcement,” Metallurgical and Materials Transactions A , vol. 36, no. 8, pp. 2253–2258, 2005. View at Scopus Z. Száraz, Z. Trojanová, M. Cabbibo, and E. Evangelista, “Strengthening in a WE54 magnesium alloy containing SiC particles,” Materials Science and Engineering A , vol. 462, no. 1-2, pp. 225–229, 2007. View at Publisher · View at Google Scholar · View at Scopus L. H. Dai, Z. Ling, and Y. L. Bai, “Size-dependent inelastic behavior of particle-reinforced metal-matrix composites,” Composites Science and Technology , vol. 61, no. 8, pp. 1057–1063, 2001. View at Publisher · View at Google Scholar · View at Scopus D. Hull and D. J. Bacon, Introduction to Dislocations , Butterworth-Heinemann, Oxford, UK, 4th edition, 2002. T. Laser, C. Hartig, M. R. Nürnberg, D. Letzig, and R. Bormann, “The influence of calcium and cerium mischmetal on the microstructural evolution of Mg—3Al—1Zn during extrusion and resulting mechanical properties,” Acta Materialia , vol. 56, no. 12, pp. 2791–2798, 2008. View at Publisher · View at Google Scholar · View at Scopus J. Bohlen, S. B. Yi, J. Swiostek, D. Letzig, H. G. Brokmeier, and K. U. Kainer, “Microstructure and texture development during hydrostatic extrusion of magnesium alloy AZ31,” Scripta Materialia , vol. 53, no. 2, pp. 259–264, 2005. View at Publisher · View at Google Scholar · View at Scopus S. F. Hassan and M. Gupta, “Development of nano-Y 2 O 3 containing magnesium nanocomposites using solidification processing,” Journal of Alloys and Compounds , vol. 429, no. 1-2, pp. 176–183, 2007. View at Publisher · View at Google Scholar · View at Scopus S. Namilae and N. Chandra, “Role of atomic scale interfaces in the compressive behavior of carbon nanotubes in composites,” Composites Science and Technology , vol. 66, no. 13, pp. 2030–2038, 2006. View at Publisher · View at Google Scholar · View at Scopus var _gaq = _gaq || []; _gaq.push(['_setAccount', 'UA-8578054-2']); _gaq.push(['_setDomainName', 'hindawi.com']); _gaq.push(['_trackPageview']); (function() { var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true; ga.src = ('https:' == document.location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s); })(); http://www.deepdyve.com/assets/images/DeepDyve-Logo-lg.png Journal of Nanotechnology Hindawi Publishing Corporation

The Overall Effects of AlN Nanoparticle Addition to Hybrid Magnesium Alloy AZ91/ZK60A

Download PDF
9 pages

Loading next page...
 
/lp/hindawi-publishing-corporation/the-overall-effects-of-aln-nanoparticle-addition-to-hybrid-magnesium-rNevdnp2xC

References

References for this paper are not available at this time. We will be adding them shortly, thank you for your patience.

Publisher
Hindawi Publishing Corporation
Copyright
Copyright © 2012 Muralidharan Paramsothy et al.
ISSN
1687-9503
eISSN
1687-9511
Publisher site
See Article on Publisher Site

Abstract

The Overall Effects of AlN Nanoparticle Addition to Hybrid Magnesium Alloy AZ91/ZK60A Hindawi Publishing Corporation Home Journals About Us About this Journal Submit a Manuscript Table of Contents Journal Menu Abstracting and Indexing Aims and Scope Annual Issues Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Reviewers Acknowledgment Subscription Information Open Special Issues Published Special Issues Special Issue Guidelines Abstract Full-Text PDF Full-Text HTML Full-Text ePUB Linked References How to Cite this Article Complete Special Issue Journal of Nanotechnology Volume 2012 (2012), Article ID 687306, 8 pages doi:10.1155/2012/687306 Research Article The Overall Effects of AlN Nanoparticle Addition to Hybrid Magnesium Alloy AZ91/ZK60A Muralidharan Paramsothy , 1 Jimmy Chan , 2 Richard Kwok , 2 and Manoj Gupta 1 1 Department of Mechanical Engineering, National University of Singapore, 9 Engineering Drive 1, 117576, Singapore 2 CTO Office, Singapore Technologies Kinetics Ltd (ST Kinetics), 249 Jalan Boon Lay, 619523, Singapore Received 5 December 2011; Accepted 11 February 2012 Academic Editor: Hongmei Luo Copyright © 2012 Muralidharan Paramsothy et al. This is an open access article distributed under the Creative Commons Attribution License , which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. Abstract A hybrid magnesium alloy nanocomposite containing AlN nanoparticle reinforcement was fabricated using solidification processing followed by hot extrusion. The nanocomposite exhibited similar grain size to the monolithic hybrid alloy, reasonable AlN and intermetallic nanoparticle distribution, nondominant ( 0 0 0 2 ) texture in the longitudinal direction, and 17% higher hardness than the monolithic hybrid alloy. Compared to the monolithic hybrid alloy, the nanocomposite exhibited higher tensile yield strength (0.2% TYS) and ultimate tensile strength (UTS) without significant compromise in failure strain and energy absorbed until fracture (EA) (+5%, +5%, −14% and −10%, resp.). Compared to the monolithic hybrid alloy, the nanocomposite exhibited unchanged compressive yield strength (0.2% CYS) and higher ultimate compressive strength (UCS), failure strain, and EA (+1%, +6%, +24%, and +6%, resp.). The overall effects of AlN nanoparticle addition on the tensile and compressive properties of the hybrid magnesium alloy is investigated in this paper. 1. Introduction Compared to aluminium, magnesium is the lightest structural metal (35% lighter) used in many engineering applications today [ 1 , 2 ]. Commercially available magnesium alloys are suitable for actual or potential use regarding weight-critical applications in the automotive, aerospace, civil infrastructure, building and construction, defence, biomedical, and sports/recreational industries [ 1 , 3 ]. In the World War 2 era, Mg-Zn alloy parts were economically manufactured and heavily used in aircraft [ 3 ]. Soon after the world war, Mg-Al alloys were also economically developed with specific metallurgical advantages over Mg-Zn alloys [ 3 ]. At present, Mg-Y and Mg-RE (Rare Earth) alloys are in development for even more specific metallurgical advantages but at generally higher cost compared to Mg-Zn and Mg-Al alloys [ 1 ]. Regardless of cast or wrought forms, Mg-Zn and Mg-Al alloys each still remain as the main classes of Mg alloys commercially in use. In the wrought form, the Mg alloys have good strength and ductility. However, wrought Mg-Zn and Mg-Al alloy nanocomposites have often demonstrated simultaneously higher strength and ductility compared to the monolithic alloys [ 4 – 14 ]. Additionally, friction stir processed Mg-Al nanocomposites have also demonstrated higher hardness and strength than the corresponding monolithic alloys [ 15 – 18 ]. Based on much of the existing representative research literature on solidification processed magnesium alloy nanocomposites, good nanoparticle distribution can be achieved in the magnesium matrix and better mechanical properties can be achieved due to the addition of nanoparticles [ 4 – 18 ]. However, it is the addition of oxide- or carbon-based nanoparticles to magnesium alloys as opposed to nitride-based nanoparticle addition that most of the research literature currently discusses. In the context of magnesium composite processing, the magnesium-oxygen strong affinity and magnesium-carbon weak affinity (comparative to each other) are both well known. On the other hand, what is not known is the affinity between magnesium and nitrogen concerning effects in magnesium nanocomposite processing (let alone solidification processing). Accordingly, one of the primary aims of this study was to simultaneously increase tensile strength and ductility of AZ91/ZK60A hybrid magnesium alloy with AlN nanoparticles. Another aim of the present study was to evaluate the compressive properties of AZ91/ZK60A/AlN hybrid alloy nanocomposite. Disintegrated melt deposition (DMD) [ 19 , 20 ] followed by hot extrusion was used to synthesize the AZ91/ZK60A/AlN hybrid alloy nanocomposite. 2. Experimental Procedures 2.1. Materials In this study, AZ91 (nominally 8.30–9.70 wt.% Al, 0.35–1.00 wt.% Zn, 0.15–0.50 wt.% Mn, 0.10 wt.% Si, 0.030 wt.% Cu, 0.005 wt.% Fe, 0.002 wt.% Ni, 0.02 wt.% others, balance Mg) and ZK60A (nominally 4.80–6.20 wt.% Zn, 0.45 wt.% Zr, balance Mg), both alloys supplied by Tokyo Magnesium Co. Ltd. (Yokohama, Japan) were used as matrix material. 3 parts AZ91 were mixed with 1 part ZK60A by mass to metallurgically downgrade AZ91. The intention of this mixing was to decrease the nominal aluminium content of AZ91 by 2 wt.%. AZ91 and ZK60A blocks were sectioned to smaller pieces. All oxide and scale surfaces were removed using machining. All surfaces were washed with ethanol after machining. AlN nanoparticles (99% purity, spherical, 10–20 nm size) supplied by Nanostructured & Amorphous Materials Inc (TX, USA) were used as the reinforcement phase. 2.2. Processing Monolithic AZ91/ZK60A hybrid alloy (nominal aluminium content of AZ91 decreased by 2 wt.%.) was cast using the DMD method [ 19 , 20 ]. This involved heating AZ91 and ZK60A blocks to 750°C in an inert Ar gas atmosphere in a graphite crucible (A12 designated size of top OD: 171 mm, bottom OD: 121 mm, height: 210 mm) using a resistance heating furnace. The crucible was equipped with an arrangement for bottom pouring. Upon reaching the superheat temperature, the molten slurry was stirred for 2.5 min at 460 rpm using a twin blade (pitch 45°) mild steel impeller to facilitate the uniform distribution of heat. The impeller was coated with Zirtex 25 (86% ZrO 2 , 8.8% Y 2 O 3 , 3.6% SiO 2 , 1.2% K 2 O and Na 2 O, and 0.3% trace inorganics) to avoid iron contamination of the molten metal. The melt was then released through a 10 mm diameter orifice at the base of the crucible. The melt was disintegrated by two jets of argon gas oriented normal to the melt stream located 265 mm from the melt pouring point. The argon gas flow rate was maintained at 25 lpm. The disintegrated melt slurry was subsequently deposited onto a metallic substrate located 500 mm from the disintegration point. An ingot of 40 mm diameter was obtained following the deposition stage. To form the AZ91/ZK60A/1.5 vol% AlN hybrid alloy nanocomposite, AlN nanoparticle powder was isolated by wrapping in Al foil of minimal weight (<0.50 wt.% with respect to AZ91 and ZK60A total matrix weight) and arranged on top of the AZ91 and ZK60A alloy blocks (see Figure 1 ), with all other DMD parameters unchanged. All billets were machined to 35 mm diameter and hot-extruded using 20.25 : 1 extrusion ratio on a 150 ton hydraulic press. The extrusion temperature was 350°C. The billets were held at 400°C for 60 min in a furnace prior to extrusion. Colloidal graphite was used as a lubricant. Rods of 8 mm were obtained. Figure 1: Arrangement of raw materials in crucible before casting for AZ91/ZK60A/AlN nanocomposite. 2.3. Heat Treatment Heat treatment was carried out on all extruded sections at 200°C for 1 hour using a resistance heating furnace. This selection of temperature and time was made in order to relax the monolithic AZ91/ZK60A hybrid alloy (nominal aluminium content of AZ91 decreased by 2 wt.%.) without recrystallization softening. The recrystallization temperature of AZ61 magnesium alloy (as the nearest matching alloy in terms of composition) following 20% cold work after 1 hour is 288°C [ 1 ]. Prior to heat treatment, the sections were coated with colloidal graphite and wrapped in aluminum foil to minimize reaction with oxygen present in the furnace atmosphere. 2.4. Microstructural Characterization Microstructural characterization studies were conducted on metallographically polished monolithic and nanocomposite extruded samples to determine grain characteristics. Hitachi S4300 Field-Emission SEM (FESEM) was used. Image analysis using Scion software was carried out to determine the grain characteristics. Thin foils were prepared from the monolithic and nanocomposite extruded samples for transmission electron microscopy (TEM) using disc punch-out and ion-milling for nanoparticle distribution observation (regarding localized effects). Goniometer XRD studies were conducted using CuK α radiation ( 𝜆 = 1 . 5 4 0 6 Å ) with a scan speed of 2°/min in an automated Shimadzu LAB-X XRD-6000 diffractometer to determine intermetallic phase(s) presence and dominant textures in the transverse and longitudinal (extrusion) directions (regarding globalised effects). 2.5. Hardness Microhardness measurements were made on polished monolithic and nanocomposite extruded samples. Vickers microhardness was measured with an automatic digital Shimadzu HMV Microhardness Tester using 25 gf-indenting load and 15 s dwell time. 2.6. Tensile Testing Smooth bar tensile properties of the monolithic and nanocomposite extruded samples were determined based on ASTM E8M-05. Round tension test samples of 5 mm diameter and 25 mm gauge length were subjected to tension using an MTS 810 machine equipped with an axial extensometer with a crosshead speed set at 0.254 mm/min. 2.7. Compressive Testing Compressive properties of the monolithic and nanocomposite extruded samples were determined based on ASTM E9-89a. Samples of 8 mm length ( 𝑙 ) and 8 mm diameter ( 𝑑 ) where 𝑙 / 𝑑 = 1 were subjected to compression using a MTS 810 machine with 0.005 min −1 strain rate. 3. Results 3.1. Macrostructural Characteristics No macropores or shrinkage cavities were observed in the cast monolithic and nanocomposite materials. No macrostructural defects were observed for extruded rods of monolithic and nanocomposite materials. 3.2. Microstructural Characteristics Microstructural analysis results revealed that grain size and aspect ratio remained statistically unchanged in the case of nanocomposite as shown in Table 1 and Figures 2(a) and 2(b) . Grain size refers to diameter of the grain assuming it is circular in shape. AlN nanoparticle reinforcement and fine intermetallic particle distributions in the nanocomposite were reasonably uniform as shown in Figure 2(c) . Table 1: Results of grain characteristics and microhardness of AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite. Figure 2: Representative FESEM micrographs showing grain size in monolithic AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite: (a) lower magnification and (b) higher magnification. (c) Representative TEM micrograph (including SAED pattern) showing the presence of individual nitride nanoparticles and fine intermetallic particles in AZ91/ZK60A/AlN nanocomposite. (d) Representative TEM micrograph (including SAED pattern) showing the presence of individual Mg-Zn rod-shaped nanoparticles in AZ91/ZK60A/AlN nanocomposite. Phases present but not labeled in the SAED patterns include Mg and Mg-Al phases only. Texture results are listed in Table 2 and shown in Figure 3 . In monolithic and nanocomposite materials, the dominant texture in the transverse and longitudinal directions was ( 1 0 − 1 1 ) . Here, extrusion did not result in the ( 0 0 0 2 ) plane being intensely parallel to the extrusion direction (as we have previously reported) [ 6 – 14 ]. Table 2: Texture results of AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite based on goniometer X-ray diffraction. Figure 3: Schematic diagram showing textures of monolithic AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite based on goniometer X-ray diffraction. In each case, vertical axis (dotted line) is parallel to extrusion direction. Each cell is made up of 2 HCP units having 1 common ( 0 0 0 2 ) basal splane. 3.3. Hardness The results of microhardness measurements are listed in Table 1 . The nanocomposite exhibited higher hardness than the monolithic material. 3.4. Tensile Behavior The overall results of ambient temperature tensile testing of the extruded materials are shown in Table 3 and Figure 4(a) . The strength of AZ91/ZK60A/1.5 vol% AlN was higher compared to monolithic AZ91/ZK60A, without significant compromise in failure strain and energy absorbed until fracture (EA). EA was determined by computing the area under the stress-strain curve up to the point of fracture. Table 3: Results of tensile testing of AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite. Figure 4: Representative: (a) tensile and (b) compressive stress-strain curves of monolithic AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite. 3.5. Compressive Behavior The overall results of ambient temperature compressive testing of the extruded materials are shown in Table 4 and Figure 4(b) . Comparing AZ91/ZK60A/1.5 vol% AlN to monolithic AZ91/ZK60A, yield strength was unchanged and ultimate strength, failure strain, and EA were each higher. Table 4: Results of compressive testing of AZ91/ZK60A and AZ91/ZK60A/AlN nanocomposite. 4. Discussion 4.1. Synthesis of Monolithic AZ91/ZK60A and AZ91/ZK60A/AlN Nanocomposite Synthesis of monolithic and nanocomposite materials, the final form being extruded rods, was successfully accomplished with no detectable metal oxidation or reaction between graphite crucible and melts. The inert atmosphere used during DMD was effective in preventing oxidation of the Mg melt. No stable carbides of Mg or Al formed due to reaction with graphite crucible. 4.2. Microstructural Characteristics Microstructural characterization of extruded samples is discussed in terms of (a) grain characteristics and (b) AlN and intermetallic nanoparticle reinforcement distribution. Nearly equiaxed grains were observed in monolithic material and nanocomposite as shown in Table 1 and Figures 2(a) and 2(b) . Grain size was statistically unchanged in the case of nanocomposite, suggesting the inability of AlN nanoparticles to serve as either nucleation sites or obstacles to grain growth during solid state cooling. It was observed that Al 12 Mg 17 and Mg 2 Zn 11 intermetallic particles decorated the grain boundaries in the monolithic material and nanocomposite. Goniometer X-ray diffraction (XRD) analysis revealed the presence of Al 12 Mg 17 and Mg 2 Zn 11 phases [ 4 , 11 ]. This was possibly due to near-homogenous (as opposed to total homogenous) mixing of AZ91 and ZK60A constituent alloys since the mixing time at 750°C before spray deposition was only a few minutes. Al 12 Mg 17 and Mg 2 Zn 11 intermetallic phases are commonly found in the individual AZ91 and ZK60A alloys, respectively [ 1 ]. The reasonably uniform distribution of AlN and intermetallic nanoparticles as shown in Figure 2(c) can be attributed to (a) minimal gravity-associated segregation due to judicious selection of stirring parameters [ 21 ], (b) good wetting of AlN nanoparticles by the alloy matrix [ 11 , 22 – 24 ], (c) argon gas disintegration of metallic stream [ 25 ], and (d) dynamic deposition of composite slurry on substrate followed by hot extrusion. In the nanocomposite, selected area electron diffraction (SAED) in TEM revealed the (a) partial reaction of AlN with the Mg alloy matrix to form Mg 3 N 2 (see Figure 2(c) ) and (b) the occurrence of Mg-Zn nanorods (not observed in the monolithic alloy, see Figure 2(d) ). Regarding the occurrence of Mg-Zn nanorods, the Mg-Zn intermetallic phase(s) precipitation was possibly regulated at nanoscale due to the presence of well-dispersed AlN nanoparticles. Dissolved Zn possibly segregated at the liquid-AlN nanoparticle interface enabling Mg-Zn intermetallic phase manipulation at the nanoscale. This is similar to possible dissolved Zn segregation at the liquid-SiC nanoparticle interface enabling nanoscale MgZn 2 precipitation as recently reported [ 26 ]. With a reasonably uniform AlN distribution throughout the AZ91/ZK60A matrix, the nanoparticle-matrix interface area was ample for effectively regulated segregation of 4.80–6.20 wt.% Zn (or 1.21–1.59 vol. % Zn) as nanoscale Mg-Zn precipitates. This was similar to that reported recently for selected ZK60A nanocomposites [ 12 – 14 ]. 4.3. Mechanical Behavior 4.3.1. Hardness A significant increase in microhardness by 17% was observed in the nanocomposite when compared to monolithic material as listed in Table 1 . This was consistent with earlier observations made on Mg/Al 2 O 3 , AZ31/C 60 and AZ31/MWCNT nanocomposites [ 16 , 17 , 27 – 29 ]. The increase in hardness of the nanocomposite in the present study can be attributed to (a) reasonably uniform distribution of harder AlN nanoparticles in the matrix and (b) higher constraint to localized matrix deformation during indentation due to the presence of nanoparticles [ 27 , 28 ]. 4.3.2. Tensile and Compressive Behavior The tensile and compressive strengths of monolithic material and nanocomposite are listed in Tables 3 and 4 (and shown in Figures 4(a) and 4(b) ), respectively. 0.2% TYS and UTS were enhanced by 5% each in AZ91/ZK60A/1.5 vol% AlN compared to monolithic material. In comparison of compressive strengths, 0.2% CYS and UCS of AZ91/ZK60A/1.5 vol% AlN were unchanged and higher by 6%, respectively, compared to monolithic material. However, the compressive stress detected at any given strain was lower for AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A as shown in Figure 4(b) . The tensile strength increase in AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A can be attributed to the following well-known factors (pertaining to reinforcement): (a) dislocation generation due to elastic modulus mismatch and coefficient of thermal expansion mismatch between the matrix and reinforcement [ 28 – 31 ], (b) Orowan strengthening mechanism [ 30 – 32 ], and (c) load transfer from matrix to reinforcement [ 28 , 30 ]. The lower compressive strength of AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A can be attributed possibly to compressive shear buckling of brittle Mg-Zn nanorods in AZ91/ZK60A/1.5 vol% AlN as illustrated in Figure 5 . The compressive shear buckling of Mg-Zn nanorods induces a slightly lower limit on the factors pertaining to reinforcement (as just described). Figure 5: Schematic diagram illustrating compressive shear buckling of brittle Mg-Zn nanorod (circled in TEM micrograph) in AZ91/ZK60A/AlN nanocomposite. 𝜏 𝑎 and 𝜏 𝑏 represent planar shear stresses where 𝜏 𝑎 < 𝜏 𝑏 . 𝜒 (exaggerated) represents very low angular deflection of the brittle Mg-Zn nanorod during buckling. In both AZ91/ZK60A/1.5 vol% AlN and monolithic AZ91/ZK60A, 0.2% TYS was about 2.21 and 2.12 times the 0.2% CYS, respectively. Here, the tensile/compressive yield stress anisotropy (0.2% TYS/0.2% CYS) was present despite the crystallographic texture exhibited where { 1 0 1 − 2 } ⟨ 1 0 1 − 1 ⟩ -type twinning was activated along the 𝑐 -axis of the HCP unit cell in Figure 3 with comparatively similar ease in both tension and compression along the 𝑐 -axis, based on the 45° angle between the 𝑐 -axis and the vertical axis [ 33 , 34 ]. The tensile/compressive yield stress anisotropy (0.2% TYS/0.2% CYS) can be attributed generally to half the strain rate used (less strain hardening) in compressive testing compared to tensile testing. The tensile/compressive yield stress anisotropy was slightly higher for AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A (2.21 compared to 2.12, resp.). This was similar to that observed in the case of selected ZK60A nanocomposites compared to monolithic ZK60A [ 12 – 14 ]. This can be attributed possibly to compressive shear buckling of brittle Mg-Zn nanorods as illustrated in Figure 5 . The brittle Mg-Zn nanorod is prone to buckling followed by fracture within the AZ91/ZK60A matrix during compressive deformation unlike during tensile deformation. The tensile and compressive failure strains of monolithic material and nanocomposite are listed in Tables 3 and 4 (and based on stress-strain curves shown in Figures 4(a) and 4(b) ), respectively. Compared to monolithic material, tensile failure strain was slightly compromised (−14%) in AZ91/ZK60A/1.5 vol% AlN. Compared to monolithic material, compressive failure strain was higher (+24%) in AZ91/ZK60A/1.5 vol% AlN. Both trends in failure strain of AZ91/ZK60A/1.5 vol% AlN compared to monolithic AZ91/ZK60A can be attributed to the presence of Mg-Zn nanorods (not observed in monolithic AZ91/ZK60A) in AZ91/ZK60A/1.5 vol% AlN (see Figure 2(d) ). Regarding the trend in tensile failure strain, it has been shown in previous studies that the nanoparticles provide sites where cleavage cracks are opened ahead of the advancing crack front. This cleavage crack opening dissipates the stress concentration that would otherwise exist at the crack front and alters the local effective stress state from plane strain to plane stress in the neighbourhood of the crack tip [ 27 , 35 ]. However, stress concentrations around the sharp ends of the Mg-Zn nanorods could not be effectively diffused by the surrounding near-spherical AlN or Mg-Al intermetallic nanoparticles. The trend in tensile failure strain can also be attributed to the partial reactivity between AlN nanoparticles and the Mg alloy matrix where Mg 3 N 2 was formed (see Figure 2(c) ). Regarding the trend in compressive failure strain, compressive shear buckling of Mg-Zn nanorods within the AZ91/ZK60A matrix (see Figure 5 ) aided in dispersing localized stored energy during compressive deformation. This allowed AZ91/ZK60A/1.5 vol% AlN to globally absorb relatively large amounts of strain energy during compressive deformation [ 12 , 36 ]. Here, Mg-Zn nanorod buckling within the AZ91/ZK60A matrix is a compressive toughening mechanism. 5. Conclusions (i) Monolithic AZ91/ZK60A and AZ91/ZK60A/1.5 vol% AlN nanocomposite can be successfully synthesized using the DMD technique followed by hot extrusion. (ii) Compared to monolithic AZ91/ZK60A, tensile strength of AZ91/ZK60A/1.5 vol% AlN was enhanced. This can be attributed to well-known factors pertaining to reinforcement. Compared to monolithic AZ91/ZK60A, compressive strength of AZ91/ZK60A/1.5 vol% AlN was decreased. This can be attributed possibly to compressive shear buckling of Mg-Zn nanorods in the nanocomposite. (iii) Compared to monolithic AZ91/ZK60A, tensile and compressive failure strains of AZ91/ZK60A/1.5 vol% AlN were slightly compromised and enhanced, respectively. The slight compromise in tensile failure strain can be attributed to (a) stress concentrations around the sharp ends of the Mg-Zn nanorods not being effectively diffused by the surrounding near-spherical AlN or Mg-Al intermetallic nanoparticles and (b) partial reactivity between AlN nanoparticles and the Mg alloy matrix where Mg 3 N 2 was formed. The enhancement in compressive failure strain can be attributed to compressive shear buckling of Mg-Zn nanorods in the AZ91/ZK60A matrix. Acknowledgments The authors wish to acknowledge National University of Singapore (NUS) and Temasek Defence Systems Institute (TDSI) for funding this research (TDSI/09-011/1A and WBS no. R265000349). References M. M. Avedesian and H. Baker, ASM Specialty Handbook: Magnesium and Magnesium Alloys , ASM International, Novelty, Ohio, USA, 1999. J. G. Kaufman, Introduction to Aluminium Alloys and Tempers , ASM International, Materials Park, Ohio, USA, 2000. E. F. Emley, Principles of Magnesium Technology , Pergamon Press, Oxford, UK, 1966. M. Paramsothy, S. F. Hassan, N. Srikanth, and M. Gupta, “Enhancing tensile/compressive response of magnesium alloy AZ31 by integrating with Al 2 O 3 nanoparticles,” Materials Science and Engineering A , vol. 527, no. 1-2, pp. 162–168, 2009. View at Publisher · View at Google Scholar · View at Scopus M. Paramsothy, S. F. Hassan, N. Q. Bau, N. Srikanth, and M. Gupta, “Selective enhancement of tensile/compressive strength and ductility of AZ31 magnesium alloy via nano-Al 2 O 3 reinforcement integration method alteration,” Materials Science Forum , vol. 618, pp. 423–427, 2009. View at Publisher · View at Google Scholar · View at Scopus M. Paramsothy, S. F. Hassan, N. Srikanth, and M. Gupta, “Simultaneous enhancement of tensile/compressive strength and ductility of magnesium alloy az31 using carbon nanotubes,” Journal of Nanoscience and Nanotechnology , vol. 10, no. 2, pp. 956–964, 2010. View at Publisher · View at Google Scholar · View at Scopus M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Carbon nanotube addition to simultaneously enhance strength and ductility of hybrid AZ31/AA5083 alloy,” Materials Sciences & Applications , vol. 2, pp. 20–29, 2011. M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “The synergistic ability of Al 2 O 3 nanoparticles to enhance mechanical response of hybrid alloy AZ31/AZ91,” Journal of Alloys and Compounds , vol. 509, no. 28, pp. 7572–7578, 2011. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Enhanced mechanical response of hybrid alloy AZ31/AZ91 based on the addition of Si 3 N 4 nanoparticles,” Materials Science and Engineering A , vol. 528, no. 21, pp. 6545–6551, 2011. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “TiC nanoparticle addition to enhance the mechanical response of hybrid magnesium alloy,” Journal of Nanotechnology , vol. 2012, Article ID 401574, 2012. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “The effective reinforcement of magnesium alloy ZK60A using Al 2 O 3 nanoparticles,” Journal of Nanoparticle Research , vol. 13, no. 10, pp. 4855–4866, 2011. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Addition of CNTs to enhance tensile/compressive response of magnesium alloy ZK60A,” Composites Part A , vol. 42, no. 2, pp. 180–188, 2011. View at Publisher · View at Google Scholar · View at Scopus M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Enhanced mechanical response of magnesium alloy ZK60A containing Si 3 N 4 nanoparticles,” Composites Part A , vol. 42, no. 12, pp. 2093–2100, 2011. View at Publisher · View at Google Scholar M. Paramsothy, J. Chan, R. Kwok, and M. Gupta, “Adding TiC nanoparticles to magnesium alloy ZK60A for strength/ductility enhancement,” Journal of Nanomaterials , vol. 2011, Article ID 642980, 2011. View at Publisher · View at Google Scholar Y. Morisada, H. Fujii, T. Nagaoka, and M. Fukusumi, “Effect of friction stir processing with SiC particles on microstructure and hardness of AZ31,” Materials Science and Engineering A , vol. 433, no. 1-2, pp. 50–54, 2006. View at Publisher · View at Google Scholar · View at Scopus Y. Morisada, H. Fujii, T. Nagaoka, and M. Fukusumi, “Nanocrystallized magnesium alloy—uniform dispersion of C 60 molecules,” Scripta Materialia , vol. 55, no. 11, pp. 1067–1070, 2006. View at Publisher · View at Google Scholar · View at Scopus Y. Morisada, H. Fujii, T. Nagaoka, and M. Fukusumi, “MWCNTs/AZ31 surface composites fabricated by friction stir processing,” Materials Science and Engineering A , vol. 419, no. 1-2, pp. 344–348, 2006. View at Publisher · View at Google Scholar · View at Scopus C. J. Lee, J. C. Huang, and P. J. Hsieh, “Mg based nano-composites fabricated by friction stir processing,” Scripta Materialia , vol. 54, no. 7, pp. 1415–1420, 2006. View at Publisher · View at Google Scholar · View at Scopus L. M. Tham, M. Gupta, and L. Cheng, “Influence of processing parameters during disintegrated melt deposition processing on near net shape synthesis of aluminium based metal matrix composites,” Materials Science and Technology , vol. 15, no. 10, pp. 1139–1146, 1999. View at Scopus M. Gupta, M. O. Lai, and S. C. Lim, “Regarding the processing associated microstructure and mechanical properties improvement of an Al-4.5 Cu alloy,” Journal of Alloys and Compounds , vol. 260, no. 1-2, pp. 250–255, 1997. View at Scopus L. M. Tham, M. Gupta, and L. Cheng, “Influence of processing parameters during disintegrated melt deposition processing on near net shape synthesis of aluminium based metal matrix composites,” Materials Science and Technology , vol. 15, no. 10, pp. 1139–1146, 1999. View at Scopus B. Q. Han and D. C. Dunand, “Microstructure and mechanical properties of magnesium containing high volume fractions of yttria dispersoids,” Materials Science and Engineering A , vol. 277, no. 1-2, pp. 297–304, 2000. View at Scopus N. Eustathopoulos, M. G. Nicholas, and B. Drevet, Wettability at High Temperatures, Vol. 3 , Pergamon Materials Series, Pergamon, New York, NY, USA, 1999. J. D. Gilchrist, Extraction Metallurgy , Pergamon Press, New York, NY, USA, 3rd edition, 1989. M. Gupta, M. O. Lai, and C. Y. Soo, “Effect of type of processing on the micro structural features and mechanical properties of Al-Cu/SiC metal matrix composites,” Materials Science and Engineering A , vol. 210, no. 1-2, pp. 114–122, 1996. View at Scopus M. De Cicco, H. Konishi, G. Cao et al., “Strong, ductile magnesium-zinc nanocomposites,” Metallurgical and Materials Transactions A , vol. 40, no. 12, pp. 3038–3045, 2009. View at Publisher · View at Google Scholar · View at Scopus S. F. Hassan and M. Gupta, “Effect of particulate size of Al 2 O 3 reinforcement on microstructure and mechanical behavior of solidification processed elemental Mg,” Journal of Alloys and Compounds , vol. 419, no. 1-2, pp. 84–90, 2006. View at Publisher · View at Google Scholar · View at Scopus S. F. Hassan and M. Gupta, “Effect of different types of nano-size oxide participates on microstructural and mechanical properties of elemental Mg,” Journal of Materials Science , vol. 41, no. 8, pp. 2229–2236, 2006. View at Publisher · View at Google Scholar · View at Scopus S. F. Hassan and M. Gupta, “Enhancing physical and mechanical properties of Mg using nanosized Al 2 O 3 particulates as reinforcement,” Metallurgical and Materials Transactions A , vol. 36, no. 8, pp. 2253–2258, 2005. View at Scopus Z. Száraz, Z. Trojanová, M. Cabbibo, and E. Evangelista, “Strengthening in a WE54 magnesium alloy containing SiC particles,” Materials Science and Engineering A , vol. 462, no. 1-2, pp. 225–229, 2007. View at Publisher · View at Google Scholar · View at Scopus L. H. Dai, Z. Ling, and Y. L. Bai, “Size-dependent inelastic behavior of particle-reinforced metal-matrix composites,” Composites Science and Technology , vol. 61, no. 8, pp. 1057–1063, 2001. View at Publisher · View at Google Scholar · View at Scopus D. Hull and D. J. Bacon, Introduction to Dislocations , Butterworth-Heinemann, Oxford, UK, 4th edition, 2002. T. Laser, C. Hartig, M. R. Nürnberg, D. Letzig, and R. Bormann, “The influence of calcium and cerium mischmetal on the microstructural evolution of Mg—3Al—1Zn during extrusion and resulting mechanical properties,” Acta Materialia , vol. 56, no. 12, pp. 2791–2798, 2008. View at Publisher · View at Google Scholar · View at Scopus J. Bohlen, S. B. Yi, J. Swiostek, D. Letzig, H. G. Brokmeier, and K. U. Kainer, “Microstructure and texture development during hydrostatic extrusion of magnesium alloy AZ31,” Scripta Materialia , vol. 53, no. 2, pp. 259–264, 2005. View at Publisher · View at Google Scholar · View at Scopus S. F. Hassan and M. Gupta, “Development of nano-Y 2 O 3 containing magnesium nanocomposites using solidification processing,” Journal of Alloys and Compounds , vol. 429, no. 1-2, pp. 176–183, 2007. View at Publisher · View at Google Scholar · View at Scopus S. Namilae and N. Chandra, “Role of atomic scale interfaces in the compressive behavior of carbon nanotubes in composites,” Composites Science and Technology , vol. 66, no. 13, pp. 2030–2038, 2006. View at Publisher · View at Google Scholar · View at Scopus var _gaq = _gaq || []; _gaq.push(['_setAccount', 'UA-8578054-2']); _gaq.push(['_setDomainName', 'hindawi.com']); _gaq.push(['_trackPageview']); (function() { var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true; ga.src = ('https:' == document.location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s); })();

Journal

Journal of Nanotechnology – Hindawi Publishing Corporation

Published: May 7, 2012

There are no references for this article.